Note: Ingredients listed on restricted chemical lists
EC/CAS
9016-87-9
Name of the chemical
4,4'-Methylendiphenyldiisocyanat tech. (Polymeres) MDI, pMDI (in Form atembarer Aerosole, A-Fraktion)
Concentration
30-<50% 10-<20%
EC/CAS
75-28-5
Name of the chemical
iso-Butan, enthält 0,1% Butadien
Concentration
2,5-<10%
General Information
Version
9 (Replaced
Revision date
2017-07-19
Product name
SpeedFix Construction 878
1.2.1 Relevant identified uses
Construction foam
1.2.2. Uses advised against
All uses not specified in this section or in section 7.3
Emergency telephone
844 892 0111
Icons in SDS
Company Information
company name
Wolf Group OÜ
e-mail address of the competent person responsible for the Safety Data Sheet
sds@wolf-group.com
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H222, H229, H302, H315, H317, H319, H334, H335, H351, H373
Hazard statements
Code
Statements
H222
Extremely flammable aerosol
Section 2
SECTION 2: Hazards identification
2.1 Classification of the substance or mixture
GB CLP Regulation (UK S.I. 2019/720 and UK S.I. 2020/1567): Classification of this product has been carried out in accordance with GB CLP Regulation (UK S.I. 2019/720 and UK S.I. 2020/1567). Acute Tox. 4: Acute toxicity if swallowed, Category 4, H302 Aerosol 1 Pressurised container May burst if heated., H229 Aerosol 1: Flammable aerosols, Category 1, H222 Carc. 2: Carcinogenicity, Category 2, H351 Eye Irrit. 2: Eye irritation, Category 2, H319 Resp. Sens. 1: Sensitisation, respiratory, Category 1, H334 Skin Irrit. 2: Skin irritation, Category 2, H315 Skin Sens. 1: Sensitisation, skin, Category 1, H317 STOT RE 2: Specific target organ toxicity, repeated exposure, Category 2, H373 STOT SE 3: Respiratory tract toxicity, single exposure, Category 3, H335
2.2 Label elements
GB CLP Regulation (UK S.I. 2019/720 and UK S.I. 2020/1567): Danger
Hazard statements
H222 - Extremely flammable aerosol. H229 - Pressurised container: May burst if heated. H302 - Harmful if swallowed. H315 - Causes skin irritation. H317 - May cause an allergic skin reaction. H319 - Causes serious eye irritation. H334 - May cause allergy or asthma symptoms or breathing difficulties if inhaled. H335 - May cause respiratory irritation. H351 - Suspected of causing cancer. H373 - May cause damage to organs through prolonged or repeated exposure.
Precautionary statements
SECTION 2: HAZARDS IDENTIFICATION (continued) P101: If medical advice is needed, have product container or label at hand. P102: Keep out of reach of children. P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P211: Do not spray on an open flame or other ignition source. P251: Do not pierce or burn, even after use. P271: Use only outdoors or in a well-ventilated area. P280: Wear protective gloves/protective clothing/respiratory protection/eye protection/protective footwear. P304+P340 IF INHALED Remove victim to fresh air and keep at rest in a position comfortable for breathing P305+P351+P338 IF IN EYES Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P410+P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122°F. P501: Dispose of contents/ container in accordance with local/regional/national/international regulation.
Supplemental label elements
EUH204: Contains isocyanates. May produce an allergic reaction.
Hazardous Ingredients
4,4´-methylenediphenyl diisocyanate, isomers and homologues; Reaction products of phosphoryl trichloride and 2-methyloxirane; Glycerol, propoxylated
Additional information
As from 24 August 2023 adequate training is required before industrial or professional use. Persons already sensitised to diisocyanates may develop allergic reactions when using this product. Persons suffering from asthma, eczema or skin problems should avoid contact, including dermal contact, with this product. This product should not be used under conditions of poor ventilation unless a protective mask with an appropriate gas filter (i.e. type A1 according to standard EN 14387) is used.
2.3 Other hazards
Product does not meet PBT/vPvB criteria