General Information
Revision date
2014-01-28
Product name
Heat Shrinkable Polymeric Products (excluding solder sleeves) RAY4566
Chemical name
Mixture of non-hazardous heat-shrinkable polymers
1.2.1 Relevant identified uses
This product is heat-shrinkable polymeric used primarily for electronic insulation, EMI/RFI
supplier name
20 Esna Park Drive
Manufacturer Name
Tyco Electronics Corporation, a TE Connectivity Ltd. company
Emergency telephone
1-800-424-9300, 1-703-527-3887, 1-800-327-6996
Icons in SDS
Company Information
company name
Tyco Electronics Corporation, a TE Connectivity Ltd. company
Section 2
SECTION 2: Hazards identification
OSHA GHS Classification Not applicable to articles
Health hazards
Reproductive/Developmental – NL None of the ingredients to which users may be exposed and which are present at equal to or greater than 0.1% of the products
Environmental hazards
Acute Toxicity – NL Target Organ Toxicity – NL Aquatic Toxicity – NL Skin Corrosion/Irritation – NL Eye Corrosion/Irritation - NL
Physical hazards
Respiratory or Skin Sensitization – NL Flammability – NL (Not flammable Mutagenicity – NL or combustible) Carcinogenicity – NL NL – Not listed. No GHS category corresponds to the low level of hazard anticipated Note: The Globally Harmonised System (GHS) for Classification had not been fully implemented in Canada at the time that this safety data sheet was developed
2.2 Label elements
As required for Finished Goods according to End-Use Products Regulations
Hazard pictograms
Not Applicable to Articles
Precautionary statements
Contact with molten material can cause burns. Avoid Contact with Mucous Membranes, Eyes, or Oral Cavity. Contact with residues from fires can cause irritation Do Not Inhale Vapours/Fumes or Particulates if overheated. of mucous membranes. EMERGENCY Product is not hazardous during proper installation. Heat-shrink tubing may emit hazardous thermal OVERVIEW: decomposition and combustion by-products if overheated to degradation or if burned. Thermal degradation and combustion by-products may include but are not limited to: carbon monoxide, carbon dioxide, aldehydes, acetic acid, low molecular weight hydrocarbons, silicon dioxide, hydrogen chloride, hydrogen fluoride, hydrogen bromide, fluoro-olefins, and oxides of nitrogen, phosphorous, and sulfur. See Section 10.
Potential health effects
EYES: Contact with molten material may cause thermal burns to the eyes and skin. If eye irritation occurs, hold eyelids apart and flush affected area(s) with clean water. Seek medical attention. SKIN: This product is not expected to be a skin irritant. No harmful effects are expected from skin absorption of this product. INGESTION: Ingestion of this product is highly unlikely. There is insufficient information available on this material to predict the effects from ingestion. INHALATION: In common with most organic materials, thermal degradation and combustion byproducts may be toxic and should not be inhaled. (See Comments below and the Thermal Degradation and Combustion Byproducts Section for more specific information.)
Acute Health Hazards
Repeated or prolonged contact may cause mild skin irritation.
Medical Conditions Generally Aggravated by Exposure
Overheating the product to charring or burning may produce vapors that may cause eye, skin, nose and throat irritation. Persons with pre-existing eye, skin, or respiratory disorders (e.g., asthma conditions) may be more susceptible to the effects of these vapors.
Additional information
None.
2.1 Classification of the substance or mixture
Not applicable to articles Health Hazards Reproductive/Developmental – NL Environmental Hazards Acute Toxicity – NL Target Organ Toxicity – NL Aquatic Toxicity – NL Skin Corrosion/Irritation – NL Eye Corrosion/Irritation - NL Physical Hazards Respiratory or Skin Sensitization – NL Flammability – NL (Not flammable Mutagenicity – NL or combustible) Carcinogenicity – NL NL – Not listed. No GHS category corresponds to the low level of hazard anticipated. Note: The Globally Harmonised System (GHS) for Classification had not been fully implemented in Canada at the time that this safety data sheet was developed.