Biomag Soluble Bulk,Blanket,Board,Paper,Module

SECTION 2: Hazards identification

None applicable chronic and possible health effects and no classification as the hazards materials May trigger temporary mechanical irritation to skin,eyes and upper respiratory tract (nose, throat & lungs), but these irritation is temporary and not allergic reaction Exposure to the fiber wool may cause moderate irritation to the eye Touch with the skin will cause the skin irritation Inhalation of airborne fiber will cause the upper respiratory tract Well-equipped personal and industrial protective parts will greatly minimize the irritation and discomforts - 2 - Part 4. FIRST AID MEASURES Eye contact: Flush eyes immediately with large amounts of clean water, rubbing eyes is prohibited for the sake of irritation increase, keep the eyelid away from the ball and the rinse should be lasted for at least 15 minutes, If irritation persists, seek medical treatment Skin contact: Take off the soiled clothing immediately and wash contacted areas with soap and water, rub and scratch is prohibited for irritation increase, using a skin cream or lotion after washing maybe helpful Inhalation: Leave the construction site for the open area with fresh air, seek medical attention if the irritation continues Gastrointestinal Irritation: If gastrointestinal tract irritation develops, move the person to a dust free area Notes to Physician: Skin and respiratory effects are resulted from the temporary mechanical irritation, the exposure of fiber will not trigger the allergic manifestations Part 5. FIRE FIGHTING MEASURES Flammable Properties: None. Hazardous Decomposition Products: None. Flash Point: None. Fire and Explosion: Non- combustible. Extinguishing Media: Use extinguishing media appropriate for type of surrounding fire. Firefighting instructions: Firefighters should wear positive pressure, self-contained breathing apparatus and full protective clothing - 3 - Part 6. ACCIDENTAL RELEASE MEASURES Carefully avoid and minimize the airborne dust. For dusty conditions, use HEPA filtered vacuum equipment if available,it’s also suitable to use a dust suppressant with sweeping; compressed air and dry sweeping are prohibited. Wear approved respiratory protection, gloves, and goggles to prevent irritation from contact and inhalation, clean the materials regularly and keep well placed in the covered container Part 7. HANDLING AND STORAGE Precautions for Handling: Handle fiber carefully to reduce the airborne dust and limit use of power tools on less in conjunction with local exhaust. Used hand tools whenever possible. Frequently clean the work area with HEPA filtered vacuum or wet sweeping to minimize the accumulation of debris, do not use compressed air for clean-up Conditions for Storage: This product is stable under all conditions of storage. Store in original containers in the dry place. Keep container closed when not in use. Empty Containers: Do not reuse the residue maybe contained in the package Part 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION Exposure Limits: OSHA PEL: Not Established OSHA PNOR: Total dust 15mg/m3; Respirable dust 5mg/m3 ACGIH TLV: None established ACGIH PNOC: Inhalable particulate 10mg/m3 Respirable dust 3mg/m3 Manufacturer’s Recommendation: Just like most industrial materials, it is prudent to reduce exposure to respirable dusts to the lowest possible level through the use of engineering controls such as ventilation and dust collection devices.Industrial hygiene standards and occupational exposure limits may vary between countries - 4 - and local jurisdictions. Contact your employer to determine which exposure levels apply to your facility. If no regulatory dust or other standards apply, a qualified industrial hygienist can assist with a specific workplace evaluation including recommendations for respiratory protection. In the absence of such guidance, the supplier recommends to control occupational AZS fiber exposure to 1 f/cc or less. Engineering controls: Use local exhaust ventilation, point of generation dust collection, downdraft workstations, emission controlling tool designs and materials handling equipment to effectively minimize exposures to respirable dust. Personal Protective Equipment: PPE-Skin Protection: Wear gloves, long-sleeved, loose-fitting clothing, and eye protection with side shields to prevent skin irritation.If possible, don’t take unwashed and soiled clothing to home, If soiled work clothing must be taken home, employers should ensure employees are trained on the best practices to minimize or avoid non work dust exposure, the washer should be thoroughly rinsed before washing clothes of other family members PPE-Eye Protection: Wear goggles or safety glasses with side shields in compliance with appropriate OSHA standards to prevent eye contact and prevent eye irritation,Do not touch eyes with soiled body parts or materials, the use of contact lenses is not recommended unless used in conjunction with appropriate eye protection PPE-Respiratory Protection: When it’s insufficient to reduce the respirable dust exposure by effective engineering and/or administrative controls, the use of appropriate respiratory protection, in accordance with the requirements of OSHA 29 CFR 1910.134 and 29,CFR 1926.103, is recommended. For dust concentrations below the applicable exposure limit value, PPE is not required. - 5 - Part 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance: white / blue in fiber wool type, odorless. Product forms include loose bulk, blanket, board, paper, module, textile Vapor pressure: Not applicable. Vapor density: Not applicable. Boiling Point: Not applicable Melting Point: 1300 °C (2372 °F) Bulk Weight (lbs/ft3) 4-10 Bulk Weight (kg/m3) 64-160 Water Solubility: Slight pH: Not applicable Evaporation rate: Not applicable Part 10. STABILITY AND REACTIVITY Chemical Stability: Stable under conditions of normal use. Conditions to avoid: None. Hazardous Polymerization: None Chemical Incompatibilities: Strong acids should be avoided