Note: Ingredients listed on restricted chemical lists
EC/CAS
1309-48-4
Name of the chemical
magnesium oxide
Concentration
20-<50%
EC/CAS
7789-75-5
Name of the chemical
Calcium fluoride
Concentration
10-<25%
EC/CAS
1344-28-1
Name of the chemical
aluminium oxide
Concentration
10-<20%
EC/CAS
7631-86-9
Name of the chemical
Silver adsorbed on silicon dioxide
Concentration
10-<20%
EC/CAS
1305-78-8
Name of the chemical
Calcium oxide
Concentration
5-<10%
EC/CAS
7440-02-0
Name of the chemical
Nickel
Concentration
1-<2.5%
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
0.1-<1%
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
0.1-<1%
General Information
Version
9.0
Revision date
2025-09-10
Product name
Lincolnweld MIL800-H PNi
1.2.1 Relevant identified uses
SAW (Submerged Arc Welding)
1.2.2. Uses advised against
Not known. Read this SDS before using this product
Emergency telephone
+1 (888) 609-1762, +1 (216) 383-8962, +1 (216) 383-8966, +1 (216) 383-8969
Icons in SDS
Company Information
company name
The Lincoln Electric Company
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H303, H317, H351, H372, H412
Hazard statements
Code
Statements
H303
May be harmful if swallowed
H317
May cause an allergic skin reaction
H351
Suspected of causing cancer
H372
Causes damage to organs through prolonged or repeated exposure
H412
Harmful to aquatic life with long lasting effects
Section 2
SECTION 2: Hazards identification
Classified according to the criteria of the Globally Harmonized System of Classification and Labeling of Chemicals (GHS). The product contains less than 0.1% of respirable crystalline silica. Emergency Overview Form Granular Physical state Solid
Hazard statements
Welding arc and sparks can ignite combustible and flammable products. Arc rays can injure eyes and burn skin. Electric shock can kill. Hazard Classification May be harmful if swallowed. May cause an allergic skin reaction. Suspected of causing cancer. Causes damage to organs respiratory tract through prolonged or repeated exposure. Harmful to aquatic life with long lasting effects.
Health hazards
Acute toxicity (Oral) Skin sensitizer Category 5 Category 1 Carcinogenicity Category 2 Specific Target Organ Toxicity - Category 1 Repeated Exposure Environmental Hazards Acute hazards to the aquatic Category 3
Environmental hazards
Chronic hazards to the aquatic Category 3
Signal word
Danger
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust/fume/gas/mist/vapors/spray. Wash face, hands and any exposed skin thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment. Wear protective gloves/ protective clothing/ eye protection/ face protection.
Response
Call a POISON CENTER or doctor/ physician if you feel unwell. IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Specific treatment (see supplemental first aid instructions on this label). Take off contaminated clothing and wash it before reuse. IF exposed or concerned: Get medical advice/attention.
Storage
Store locked up.
Disposal
Dispose of contents/ container to an approved facility in accordance with local, regional, national and international regulations.
Other hazards which do not result in classification
Electrical Shock can kill. If welding must be performed in damp locations or with wet clothing, on metal structures or when in cramped positions such as sitting, kneeling or lying, or if there is a high risk of unavoidable or accidental contact with work piece, use the following equipment: Semiautomatic DC Welder, DC Manual (Stick) Welder, or AC Welder with Reduced Voltage Control. Arc rays can injure eyes and burn skin. Welding arc and sparks can ignite combustibles and flammable materials. Overexposure to welding fumes and gases can be hazardous. Read and understand the manufacturer’s instructions, Safety Data Sheets and the precautionary labels before using this product. Refer to Section 8. Substance(s) formed under the The welding fume produced from this welding electrode may contain the conditions of use following constituent(s) and/or their complex metallic oxides as well as solid particles or other constituents from the consumables, base metal, or base metal coating not listed below. This product contains a non-hazardous polymer that may produce airborne fluoride compounds during thermal decomposition. Use with adequate ventilation. If symptoms such as respiratory irritation or irritation to eyes, nose or throat occur, or ventilation cannot prevent airborne overexposures, use a respirator that provides protection for hydrogen fluoride/acid gases, in accordance with levels present in the work environment. Chemical Identity Carbon dioxide Carbon monoxide Nitrogen dioxide Ozone CAS-No. 124-38-9 630-08-0 10102-44-0 10028-15-6
2.1 Classification of the substance or mixture
Health Hazards Acute toxicity (Oral) Category 5 Skin sensitizer Category 1 Carcinogenicity Category 2 Specific Target Organ Toxicity - Category 1 Repeated Exposure Environmental Hazards Acute hazards to the aquatic Category 3 environment Chronic hazards to the aquatic Category 3 environment