Fleetweld 5P

2.1 Classification of the substance or mixture

OSHA Not classified as hazardous according to applicable GHS hazard classification criteria.

Hazard pictograms

No symbol

Signal word

No signal word.

Hazard statements

Not applicable

Precautionary statements

Not applicable Other hazards which do not Electrical Shock can kill. If welding must be performed in damp locations or result in GHS classification: with wet clothing, on metal structures or when in cramped positions such as sitting, kneeling or lying, or if there is a high risk of unavoidable or accidental contact with work piece, use the following equipment: Semiautomatic DC Welder, DC Manual (Stick) Welder, or AC Welder with Reduced Voltage Control. Arc rays can injure eyes and burn skin. Welding arc and sparks can ignite combustibles and flammable materials. Overexposure to welding fumes and gases can be hazardous. Read and understand the manufacturer’s instructions, Safety Data Sheets and the precautionary labels before using this product. Refer to Section 8. Substance(s) formed under the The welding fume produced from this welding electrode may contain the conditions of use: following constituent(s) and/or their complex metallic oxides as well as solid particles or other constituents from the consumables, base metal, or base metal coating not listed below. Chemical Identity CAS-No. Carbon dioxide 124-38-9 Carbon monoxide 630-08-0 Nitrogen dioxide 10102-44-0 Ozone 10028-15-6 Manganese 7439-96-5 Reportable Hazardous Ingredients Mixtures Chemical Identity CAS number Content in percent (%)* lron 7439-89-6 80 - <100% Cellulose, pulp 65996-61-4 1-<5% Sodium silicate 1344-09-8 1-<5% Titanium dioxide (naturally occurring) 13463-67-7 1-<5% Manganese 7439-96-5 0.1-<1% lron oxide 1309-37-1 0.1-<1% Magnesite 546-93-0 0.1-<1% Silicon dioxide (amorphous) 7631-86-9 0.1-<1% Aluminum oxide 1344-28-11 0.1-<1% Magnesium oxide 1309-48-4 0.1-<1% Carbon 7440-44-0 0.1-<1% * All concentrations are percent by weight unless ingredient is a gas. Gas concentrations are in percent by volume. Composition Comments: The term “Hazardous Ingredients” should be interpreted as a term defined in Hazard Communication standards and does not necessarily imply the existence of a welding or allied process hazard. The product may contain additional non-hazardous ingredients or may form additional compounds under the condition of use. Refer to Sections 2 and 8 for more information. Ingestion: Avoid hand, clothing, food, and drink contact with fluxes, metal fume or powder which can cause ingestion of particulate during hand to mouth activities such as drinking, eating, smoking, etc. If ingested, do not induce vomiting. Contact a poison control center. Unless the poison control center advises otherwise, wash out mouth thoroughly with water. If symptoms develop, seek medical attention at once. Inhalation: Move to fresh air if breathing is difficult. If breathing has stopped, perform artificial respiration and obtain medical assistance at once. Skin Contact: Remove contaminated clothing and wash the skin thoroughly with soap and water. For reddened or blistered skin, or thermal burns, obtain medical assistance at once. Eye contact: Dust or fume from this product should be flushed from the eyes with copious amounts of clean, tepid water until transported to an emergency medical facility. Do not allow victim to rub or keep eyes tightly closed. Obtain medical assistance at once. Arc rays can injure eyes. If exposed to arc rays, move victim to dark room, remove contact lenses as necessary for treatment, cover eyes with a padded dressing and rest. Obtain medical assistance if symptoms persist. Most important symptoms/effects, acute and delayed Symptoms: Short-term (acute) overexposure to fumes and gases from welding and allied processes may result in discomfort such as metal fume fever, dizziness, nausea, or dryness or irritation of nose, throat, or eyes. May aggravate pre-existing respiratory problems (e.g. asthma, emphysema). Long-term (chronic) overexposure to fumes and gases from welding and allied processes can lead to siderosis (iron deposits in lung), central nervous system effects, bronchitis and other pulmonary effects. Refer to Section 11 for more information.

SECTION 2: Hazards identification

The hazards associated with welding and its allied processes such as soldering and brazing are complex and may include physical and health hazards such as but not limited to electric shock, physical strains, radiation burns (eye flash), thermal burns due to hot metal or spatter and potential health effects of overexposure to fumes, gases or dusts potentially generated during the use of this product. Refer to Section 11 for more information. Indication of immediate medical attention and special treatment needed Treatment: Treat symptomatically. General Fire Hazards: As shipped, this product is nonflammable. However, welding arcs, sparks, open flames, and hot surfaces associated with welding, brazing, and soldering can ignite combustible and flammable materials. Implement fire protection measures according to the place of use risk assessment, local regulations, and all relevant safety standards. Read and understand the American National Standard 249.1, "Safety in Welding, Cutting, and Allied Processes," and the National Fire Protection Association NFPA 51B, "Standard for Fire Prevention during Welding, Cutting, and Other Hot Work," before using this product. Suitable (and unsuitable) extinguishing media Suitable extinguishing media: As shipped, the product will not burn. In case of fire in the surroundings: use appropriate extinguishing agent. Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire. media: Specific hazards arising from Welding arc and sparks can ignite combustibles and flammable products. the chemical: Special protective equipment and precautions for fire-fighters Special fire-fighting Use standard firefighting procedures and consider the hazards of other procedures: involved materials. Special protective equipment Selection of respiratory protection for fire fighting: follow the general fire for fire-fighters: precautions indicated in the workplace. Self-contained breathing apparatus and full protective clothing must be worn in case of fire. Personal precautions, If airborne dust and/or fume is present, use adequate engineering controls protective equipment and and, if needed, personal protection to prevent overexposure. Refer to emergency procedures: recommendations in Section 8. Methods and material for Absorb with sand or other inert absorbent. Stop the flow of material, if this is containment and cleaning up: without risk. Clean up spills immediately, observing precautions in the personal protective equipment in Section 8. Avoid generating dust. Prevent product from entering any drains, sewers or water sources. Refer to Section 13 for proper disposal. Environmental Precautions: Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Do not contaminate water sources or sewer. Environmental manager must be informed of all major spillages. Precautions for safe handling: Prevent formation of dust. Provide appropriate exhaust ventilation at places where dust is formed. Read and understand the manufacturer's instruction and the precautionary label on the product. Refer to Lincoln Safety Publications at www.lincolnelectric.com/safety, ISO/TR 18786:2014, ISO/TR 13392:2014, American National Standard 249.1, "Safety In Welding, Cutting and Allied Processes" published by the American Welding