Thermofit S1006 Adhesive, Parts A and B

Hazard statements (CLP)

H315, H317, H320, H335

Code

Statements

H315

Causes skin irritation

SECTION 2: Hazards identification

GHS Classification EMERGENCY OVERVIEW: This two-part epoxy resin consists of a viscous purple liquid (Part A) and a viscous tan liquid with an ammonia odor (Part B). Avoid all personal contact. Causes skin and eye irritation and burns.

Signal word

Warning HAZARD STATEMENT(S) H315 Causes skin irritation H317 May cause an allergic skin reaction H320 Causes eye irritation H335 May cause respiratory irritation

Precautionary statements

P210 Keep away from heat/sparks/open flames/hot surfaces. No smoking. P264 Wash skin thoroughly after handling. P270 Do not eat, drink or smoke when using this product. P271 Use only outdoors or in a well-ventilated area. P273 Avoid release to the environment P280 Wear protective gloves/eye protection/face protection. P302 + P352 IF ON SKIN: Wash with plenty of soap and water. P304 + P340 IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P312 Call a POISON CENTER or doctor/physician if you feel unwell. P331 Do NOT induce vomiting. P332 + P313 If skin irritation occurs: Get medical advice/attention. P337 + P313 If eye irritation persists: Get medical advice/attention. P363 Was contaminated clothing before reuse. P370 + P378 In case of fire: Use carbon dioxide, dry chemical, or foam to extinguish. P403 + P233 Store in a well-ventilated place. Keep container tightly closed. P501 Dispose of contents/container to an approved waste disposal facility. HMIS HAZARD CLASSIFICATIONS (US/CN/EU): Part A HEALTH: 2 FLAMMABILITY: 2 REACTIVITY: 0 PROTECTION: See PPE section. Part B HEALTH: 1 FLAMMABILITY: 1 REACTIVITY: 0 PROTECTION: See PPE section.

Potential health effects

Health Effects/Symptoms of Exposure: Proper installation of this product creates no known acute or chronic health hazards.

Acute Health Hazards

EYES: Part A: This material is an eye irritant. Direct contact with the liquid or exposure to vapors or mists may cause stinging, tearing, redness, and swelling. Contact with molten material may cause thermal burns. Persons with pre-existing eye disorders may be more susceptible to the effects of this material. Part B: This material is a severe eye irritant. Direct contact with the liquid or exposure to vapors or mists may cause stinging, tearing, redness, swelling, and eye damage. Persons with pre-existing eye disorders may be more susceptible to the effects of this material. SKIN: Part A: This material is a skin irritant. Direct contact or exposure to vapors or mists may cause redness, burning, and skin damage. Repeated contact may cause an allergic skin reaction in sensitized individuals. Persons with pre-existing skin disorders may be more susceptible to the effects of this material. Contact with molten material may cause thermal burns. Part B: This material may cause mild skin irritation. Prolonged or repeated contact or exposure to vapors or mists may cause redness and burning. Persons with pre-existing skin disorders may be more susceptible to the effects of this material. SKIN Part A: No harmful effects are expected from skin absorption of this material. ABSORPTION: Part B: Contact with this material may result in skin absorption but this route alone under normal conditions of use does not anticipate symptoms of toxicity. INGESTION: Part A: Ingestion of this material is highly unlikely. However, in the event such an exposure should occur, this product is expected to have a low degree of toxicity by ingestion. Part B: This material may be harmful or fatal if swallowed. Ingestion may result in severe irritation and burns of the mouth, throat, and digestive tract. INHALATION: Part A: Because of its low volatility, exposure to vapors is unlikely. In common with most organic materials, degradation and combustion byproducts may be toxic and should not be inhaled. See comments below and Section 5: FIRE FIGHTING MEASURES (Hazardous Combustion Products) for more specific information. Part B: Exposure to vapours or fumes may cause irritation of the respiratory tract. Pre-existing lung disorder (e.g., asthma-like conditions) may be aggravated by exposure to this material.

Health hazards

Part A and part B of this product have no known significant effects or critical hazards. For further information, see Section 11: TOXICOLOGICAL INFORMATION (Mutagenicity).

Medical Conditions Generally Aggravated by Exposure

Overheating the material to temperatures above 149°C (300°F) may produce vapors that may cause eye, skin, nose, and throat irritation. Respiratory symptoms associated with pre-existing lung disorders (e.g., asthma-like conditions) may be aggravated by exposure to overheated material.

Additional information

None

2.1 Classification of the substance or mixture

Eye Irritant (Category 2A) Parts A & B