Ultralane Stripper part B

Hazard statements (CLP)

H302, H314, H318, H400

Code

Statements

H302

Harmful if swallowed

SECTION 2: Hazards identification

GHS CLASSIFICATION OF SUBSTANCE OR MIXTURE Skin corrosion Category 1, H314 Eye damage Category 1, H318 Acute Toxicity, Oral Category 4, H302 Aquatic Toxicity, Acute Category 1, H400

Signal word

Danger!

Hazard statements

302 Harmful if swallowed H318 Causes serious eye damage H314 Causes severe skin burns and eye damage H400 Very toxic to aquatic life

Prevention

P202 Do not handle until all safety precautions have been read and understood. P260 Do not breathe mists. P264 Wash hands thoroughly after handling, P270 Do not eat, drink or smoke when using this product. P273 Avoid release to the environment. P280 Wear protective gloves, clothing, and eye/face protection.

Response

P301+P330+P331+P312 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Call POISON CENTER and/or doctor if you feel unwell, P303+P361+P364+P353+P352 IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water/shower. Wash with plenty of soap and water. P333+P313 If skin irritation or rash occurs: Get medical attention. P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P308+P313 IF exposed or concerned: Get medical attention. P391 Collect spillage.

Storage

P403+P233 Store in a well-ventilated place. Keep container tightly closed. P4085 Store locked up. (Printed: 9/8/2021 I Ultralane Stripper part B [ Page 1 of 6 See toxicological information (section 11) Not otherwise classified or not covered by GHS lachrymator General Information: Read entire MSDS for a more thorough evaluation of the hazards

2.1 Classification of the substance or mixture

Skin corrosion: Category 1, H314 Eye damage: Category 1, H318 Acute Toxicity, Oral: Category 4, H302 Aquatic Toxicity, Acute: Category 1, H400 GHS LABEL ELEMENTS: HAZARD SYMBOLS: SIGNAL WORDS: Danger! HAZARD STATEMENTS: 302 Harmful if swallowed H318 Causes serious eye damage H314 Causes severe skin burns and eye damage H400 Very toxic to aquatic life PRECAUTIONARY STATEMENTS: PREVENTION: P202 Do not handle until all safety precautions have been read and understood. P260 Do not breathe mists. P264 Wash hands thoroughly after handling, P270 Do not eat, drink or smoke when using this product. P273 Avoid release to the environment. P280 Wear protective gloves, clothing, and eye/face protection. RESPONSE: P301+P330+P331+P312 IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Call POISON CENTER and/or doctor if you feel unwell, P303+P361+P364+P353+P352 IF ON SKIN (or hair): Take off immediately all contaminated clothing and wash before reuse. Rinse skin with water/shower. Wash with plenty of soap and water. P333+P313 If skin irritation or rash occurs: Get medical attention. P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P308+P313 IF exposed or concerned: Get medical attention. P391 Collect spillage. STORAGE: P403+P233 Store in a well-ventilated place. Keep container tightly closed. P4085 Store locked up. (Printed: 9/8/2021 I Ultralane Stripper part B [ Page 1 of 6 See toxicological information (section 11) Hazards Not otherwise classified or not covered by GHS: lachrymator General Information: Read entire MSDS for a more thorough evaluation of the hazards {3. Composition / Information on Ingredients Name CAS Number % Ammonium hydroxide 1336-21-6 10-30 Amounts specified are typical and do not represent a specification. Remaining components are proprietary, non- hazardous, and/or present at amounts below reportable limits. (4. First Aid Measures ] Eye Contact: Check for and remove any contact lenses. Immediately flush eyes for at least 15 minutes with running water. Hold eyelids apart to ensure rinsing of the entire eye surface and lids with water. Getimmediate medical attention. Skin Contact: In case of contact, wash affected areas with plenty of water, and soap, if available, for several minutes. Remove and clean contaminated clothing and shoes before re-use, Get medical attention if initation occurs. Inhalation: Move exposed person to fresh air. If not breathing, give artificial respiration or oxygen. If breathing is difficult, transport to medical care and, if available, give supplemental oxygen. Loosen tight clothing such as a collar, tie, belt, or waistband, Get immediate medical attention, Ingestion: Wash out mouth with water. If swallowed dilute by giving two (2) glasses water to drink. Do not induce vomiting until direct to do so by medical personnel. Never give anything by mouth to an unconscious person. Get immediate medical attention, Note to physician: No specific treatment. Treat symptomatically. Call poison control center if large quantities were ingested |S. _Fire-Fighting Measures Flash point: Not applicable (water based solution) Hazardous Thermal Decomposition products may include the following materials: nitrogen oxides and ammonia Decomposition Products: Extinguishing Media: Carbon dioxide, foam, dry chemical, water spray as suitable for the surrounding fire. Special Exposure Hazards: Promptly isolate the scene by removing all persons from the vicinity of the fire. No actions shall be taken involving any personal risk or without suitable training Special Protective equipment Fire-fighters should wear appropriate protective equipment and self-contained breathing for fire-fighters: apparatus (SCBA) with a full face-piece operated in positive pressure mode. (&. Accidental Release Measures Personal Precautions: No actions shall be taken involving any personal risk or without suitable training. Evacuate ‘surrounding areas, Keep unnecessary and unprotected personnel from entering area. Do not touch or walk through spilled material, Avoid breathing vapor or mist and provide adequate ventilation, Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment (see Section 8). Environmental Avoid dispersal of spilled material and runoff that leads to contact with soil, waterways, drains, Precautions: and sewers, Inform the relevant authorities if the product has caused environmental pollution, Methods of Clean Up: Stop leak if without risk. Move containers from spill area. Approach spill from up wind if possible. Prevent spill from entering sewers, rivers and other water courses, basements, or confined areas. Wash into effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material (e.g. sand, earth, vermiculite, or diatomaceous earth) and place in container for disposal according to local regulations. Dispose of only using a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see section 1 for emergency contact information (Printed: 9/8/2021 L Ultralane Stripper part B I Page 2 of 6 (7. Handling and Storage J Handling: Wear appropriate personal protective equipment (see Section 8) when handling. Eating, drinking, and smoking should be prohibited in areas where chemical are handled, stored, or processed. Workers should wash hands and face before eating, drinking, and smoking. Remove contaminated clothing and protective equipment before entering eating areas. Persons with a history of skin sensitization problems should not be employed In processes where this material is used. Keep in the original container or a suitable alternate made from a compatible material. Keep ail containers tightly closed when not in use. Empty containers retain product residue and should be disposed of properly. Do not reuse empty containers for other purposes or to hold other materials. Storage: Store in accordance with loca! regulations. Store in original containers, at 10°C - 35°C. Keep away from incompatible materials (see Section 10) and food and drink. Keep all containers tightly closed when not in use and tightly re-seal after use. Do not store in untabeled containers. Use appropriate containment to avoid environmental contamination. 8. Exposure Controls / Personal Protection | Ammonium ACGIH Threshold Limit Values: TWA 25 ppm, STEL 35ppm hydroxide NIOSH Recommended: TWA 25 ppm or 18 mg/m? Recommended [f this product contains ingredients with exposure limits, personal, workplace, atmospheric, or biological Monitoring monitoring may be required to determine the effectiveness of the ventilation system or other control Procedures: measures and/or to determine whether it is necessary to use respiratory protective equipment. {t will also be necessary to reviewed national guidance documents for determining how to handle and relevant Hazardous Substances Engineering No special ventilation requirements are necessary for this product. Good general ventilation should be measures: sufficient to contro! worker exposure to airbome contaminants. If this product contains ingredients with exposure limits, use process enclosures, local exhaust ventilation, or other engineering controls to keep worker exposure below the recommended or statutory limits Hygiene Wash hands, forearms, and face thoroughly after handling any chemical products, before eating, measures: smoking, and using the lavatory and at the end of the work period. Appropriate techniques should be used to remove potentially contaminated clothing. Contaminated clothing should not be allowed out of the workplace. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Personal Protection Respiratory: tn case of inadequate ventilation wear respiratory protection. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator. Hands: Chemical Resistant, impervious gloves that comply with an approved safety standard should be worn always when handling chemical products if a risk assessment indicates that this is necessary. Consider the parameters specified by the glove manufacture and check gloves during use to ensure they are retaining their protective properties. Nitrile Rubber gloves with a thickness of 0.114mm or a breakthrough time of 240 minutes or longer are generally suitable for limited/splash contact. Butyl Rubber gloves with a thickness of 0.3mm or a breakthrough time of 48 minutes or longer may be more suitable for full contact. Eyes: Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, or dusts. If contact is possible, at a minimum use chemical splash googles. if significant splash hazard may occur, consider using a full- face shield. Skin: Personal Protective equipment for the body should be selected based on the task being performed and the risks invoived. Typical protective equipment includes non-absorbent lab coats, disposabie protective sleeves, coats, or whole-body suits. See a safety specialist to determine the appropriate level of protection for your task. Environmental Emissions from ventilation or work processes should be checked to ensure they comply with the Exposure requirements of environmental regulations. In some cases, fume scrubbers, filters, or engineering Controls: medifications to the process equipment will be necessary to reduce emissions to acceptable levels. p. Physical and Chemical Properties | Appearance: Clear liquid Oder Strong ammonia odor Boiling Point: >38°C (initlal) Freezing Point: Not determined { Printed: 9/8/2021 | Ultralane Stripper part B | Page3of 6 | Flash Point: Not applicable pH: 17 Auto-ignition Temperature: Not determined Flammable Limits: Not determined Vapor Pressure: 115 mm Hg at 20°C (68°F) Water Solubility: completely soluble Specific Gravity: 0.9 Vapor Density: 1.21 (Air = 1) Evaporation Rate: (butyl acetate =1) voc: O g/L (estimated) Viscosity: Not determined fio. Stability and Reactivity } Chemica! Stability: This product is stable, under normal conditions of storage end use, hazardous reactions will not occur. Hazardous Polymerization: Hazerdous polymerization will not occur. Conditions to Avoid: High temperatures and exposure to strong oxidizing agents and strong acids. Exposure to aluminum or atuminum alloys may cause a reaction with product, which may generate significant heat and/or noxious eases, Incompatible Materiats: Copper, tron, Zinc, Aluminum and Aluminurn Alloys. Hazardous Decomposition Nitrogen oxides, Ammonia [ 11. Toxicological Information | cute Toxici Productingredient Name _| Test | Endpoint | Species | Result | Product | : [_OraiLoso | Rat | 350 mg/kg J irritation / Corrosion Product/Ingredient Namo __{ Test | Specios | Result | |_No data available | ensitizer ! Product/ingredient Name | Test | Species | Result ] [_No data avallable L_., | utagenici Product/ingredient Name_| Test | Resutt | No data available Conetusion/ Summary; the weight of scientific evidence indicates that the components of this product are not genotoxic Carcinogenicity No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC, ACGIH,NTP or OSHA or : Reproductive Toxici __ Product/ingredient Name__| Test | Species Maternal Toxicity [Fertility |_ Developmental Effects No data available | Teratogenici Product/Ingredient Namo __| Test [Species | Results No data available | { ‘otential Acute Healt! fects Inhalation: May cause imitation or bums. Ingestion: Harmful if swallowed Skin Contact: Causes severe skin burns Eye Contact: Causes serious eye damage Potential Chronic Health Effects Productfingradiont Namo _| Test | Endpoint Species | Results | No Data Available | J General: Once sensitized, an allergic reaction may occur when subsequently exposed to very low levels Target Organs: No known significant effects or critical hazerds Carcinogenicity: No known significant effects or critical hazerds Mutagenicity: No known significant effects or critical hazards Teratogenicity: No known significant effects or critical hazards Ooevelopmental Effects: No known significant effects or critical hazards Fertility Effects: No known significant effects or critical hazerds { Printed: 9/8/2021 | Uitralane Stripper part B | Page 4 of 6 (42. Ecological Information Environmental Effects: Acutely toxic to aquatic organisms. May be harmful to the environment if released in large quantities. Aquatic Ecotoxici Product/ingredient Name _| Test T Endpoint | Exposure [Species | Result | [Product I = [ Acute LC50_| ‘50 hours [Daphnia | 32mgi_| Persistence and Dearadabii Product/Ingredient Name _| Test i Period T Result I | [No dat Tabi I 1 | © data avarable [Product/ingredient Name [ Aquatic half-life i Photolysis. | Biodegradability ] I No data available I No data available [_Nodata available _| Bioaccumulative potential Product/ingredient Name I Log Pow i BCF i Potential I Other adverse effects: No known significant effects or critical hazards Other information: BODS: Not determined COD: Not Determined TOC: Not determined [13. Disposal Consideration Waste Disposal Method: Disposal of this products, solutions, and by-products should at all times comply with the requirements of environmental and waste disposal legislation and any regional or local authority requirements. Dispose of surplus, non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed on untreated to the sewer system unless this is complaint with all applicable laws and regulations. Incineration by an approved and licensed contractor is the most common disposal method. Packaging materials that and absorbents containing the product can typically be landfilled or incinerated. Contact local authorities to determine the proper means of disposal in your area. (44. Transport Information Bor: Neo Bull , Ammonia Sout UN/ID Number UN2672 ‘roper Shipping Name: mmonia Solutions Hazard Class: 8 Label: Corrosive Packing Group: Ill Environmental Hazards Marine Pollutant IATA: Non-Bulk UN/ID Number UN2672 Proper Shipping Name: Ammonia Solutions Hazard Class: 8 Label: Corrosive Packing Group: Environmental Hazards Marine Pollutant Note: Ammonia content is between 10% and 30% by weight 15. REGULATORY INFORMATION US Federal Requlation: Occupational Safety and Health Act (OSHA): This product is a hazardous chemical under the OSHA Hazard Communication Standard (29 CFR 1910.1200). Resource Conservation and Recovery Act (RCRA): This product is a hazardous waste under RCRA (40 CFR 261). SARA Title Ill: Section 304 - CERCLA: This product does not contain chemicals regulated under Section 304 as extremely hazardous substance(s) for emergency release notification ("CERCLA List): Ingredient CAS # Component RQ (Ibs) Calculated Product RQ (Ibs) ‘Ammonia Hydroxide 1336-21-6 1000 >3,300 SARA Title Ill: Section 311/312 - Hazard Communication Standard (HCS): Immediate (acute) health hazard SARA Title Ill: Section 313 Toxic Chemical List (TCL): This product does contain a toxic chemical for routine annual Toxic Chemical Release Reporting under section 313 (40 CFR 372). Ammonia Hydroxide CAS #: 1336-21-6 TSCA 8(b) - y Status: All chemi \(s) comprising this product are listed on the TSCA inventory. (Printed: 97/8/2021 I Ultralane Stripper part 8 l Page5of6 | TSCA Section 12(b) - Export Notification: This product does not contain chemicals which are subject to Section 12(b) export notification: State Requlations: California Proposition 65: This product does not contain any chemicals currently on the California list of Known Carcinogens and Reproductive Toxins. International Requlations: REACH Status (EC 1907/2006): This material has been registered, pre-registered, or is otherwise exempt from registration under REACH. REACH Annex XIV (SVHC): No listed components as of validation date Reach Annex XVIII (Restrictions on the manufacture, placing on the market & use of certain dangerous substances, mixtures, and articles): No list components as of validation date WHMIS: 1B - Poisonous and infectious material - Immediate and serious effects - Toxic International Lists: Australia Inventory (AICS): all components are listed or exempt Malaysia Inventory (EHS register): not determined Canadian Inventory (CEPA-DSL): all components are listed or exempt New Zedand Inv. of Chem. (NZIoC}: all components are listed or exempt China Inventory (IECSC): all components are listed or exempt Philippines Inventory (PICS): ail components are listed or exempt Japan Inventory (ENCS}: al components are listed or exempt Taiwan Inventory (CSN): not determined Korea Inventory (ECL) al components are listed or exempt 16. OTHER INFORMATION Hazardous Material Information System (HMIS) - USA & National Fire Protection Association (USA): vS Personal Protection “Zuggested minimum personal protection equpment End usar Must celarmifne appt opiataress Of thave suggestions for ray appleatons and usage Condens. MSDS No: UltraStripB-20170822 Reason Issued: update Pr 1d By: cM A \d By: repared CM By Title: oh Vice President proves eer ei NOTICE TO READER: While the information and recommendations in this publication are to the best of our knowedge, information and belief accurate atthe date of publication, NOTHING HEREIN IS TO BE CONSTRUED AS A WARRANTY, EXPRESS OR OTHERWISE. IN ALL CASES, IT IS THE RESPONSIBILITY OF THE USER TO DETERMINE THE APPLICABILITY OF SUCH INFORMATION AND RECOMMENDATIONS AND THE SUITABILITY OF PRODUCTS FOR THE USER'S PARTICULAR PURPOSE(S). THIS PRODUCT MAY PRESENT HAZARDS AND SHOULD BE USED WITH CAUTION. WHILE CERTAIN HAZARDS ARE DESCRIBED IN THIS PUBLICATION, NO GUARANTEE IS MADE THAT THESE ARE THE ONLY HAZARDS THAT EXIST. The product(s) has not been tested for, and is therefore not recommended for, uses for which prolonged contact with mucous membranes, abraded skin, or blood is intended; or for uses for which implantation within the human body is intended. (Printed: 9/8/2021 I Ultralane Stripper part B Page 6 of 6 ]