4708-E12599 YELLOW GLOSS AIR DRY

Acute Health Hazards

EFFECTS OF OVEREXPOSURE: SKIN CONTACT: Moderate irritation possible from prolonged exposure; defatting and dermatitis. EYE CONTACT: Moderate irritation, redness, tearing and itching sensation. INHALATION: May cause nasal irritation, headache, dizziness, nausea, weakness or vomiting. Loss of consciousness. INGESTION: Can cause gastrointestinal irritation, headache, dizziness, nausea and weakness. ACUTE: Can cause moderate skin irritation, defatting, dermatitis and tingling sensation. Can cause moderate eye irritation, redness, tearing and blurred vision. CHRONIC: May produce liver and kidney damage, persistent coughing, brain damage and may be fatal. CARCINOGENICITY: This product

Contains

(Chemical; CAS#) # Phenylethane 100-41-4 # Titanium Dioxide 13463-67-7 # Indicates a chemical listed by IARC 2B as a possible carcinogen. See Section XI. MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE: Pre-existing respiratory conditions, Pre-existing skin disorders, liver and kidney disorders and allergies.

Principle Routes of Exposure

OF EXPOSURE: Dermal and Inhalation EMERGENCY AND FIRST AID PROCEDURES: EYE CONTACT: Flush with large quantities of water for 15 to 30 minutes. Get medical attention. SKIN CONTACT: Wash exposed area with mild soap and water for 15 minutes. Remove contaminated clothing. INHALATION: Remove victim to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration. Get immediate medical attention. INGESTION: < DO NOT INDUCE VOMITING > Keep victim warm and seek immediate medical attention. Continued on next page. SECTION VI REACTIVITY DATA STABILITY: Stable. HAZARDOUS POLYMERIZATION Will not occur CONDITIONS TO AVOID Extremely high temperatures INCOMPATIBILITY MATERIALS TO AVOID) Avoid contact with strong oxidizing agents HAZARDOUS DECOMPOSITION OR BY PRODUCTS Hazardous decomposition may produce carbon dioxide and/or carbon monoxide SECTION VII SPILL AND LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Refer to other sections in this document Eliminate all sources of ignition Absorb liquid in absorbent material 1.e dry sand or earth), then place in a chemical waste container for proper disposal Prevent spreading to ground water Avoid runoff into storm sewers and ditches that lead to waterways WASTE DISPOSAL METHOD Recycle whenever possible or destroy by liquid incineration in accordance with applicable regulations Contaminated absorbent should be incinerated or sent to an approved landfill in accordance with Local, State, and Federal Regulations SECTION VIII SAFE HANDLING AND USE INFORMATION RESPIRATORY PROTECTION If TLV of the product or any component is exceeded, a NIOSH approved Air Supplied Respirator is advised in absence of environmental control.

Precautionary statements

TO BE TAKEN IN HANDLING AND

Storage

Containers may be hazardous when emptied, since emptied containers may retain product residuals (Vapors, Liquid, and/or Solids), All precautions given in this data sheet must be observed. Store at room temperature away from heat sources, and have lids tightly closed. OTHER PRECAUTIONS: Paint and solvents have been linked liver abnormalities, kidney and lung damage. For Industrial Use Only with adequate ventilation. Follow precautions of this Material Safety Data Sheet to prevent exposure. SECTION X SHIPPING INFORMATION D.O.T. SHIPPING NAME Paint D.O.T. HAZARD CLASS 3 UN/NA NUMBER UN1263 PACKAGING GROUP PG II D.O.T. LABELS REQUIRED Flammable SECTION XI OTHER REGULATORY INFORMATION Toxic Control Act: All components of this product are listed on the EPA TSCA Inventory or exempt from notification. Canadian Environmental Protection: All of the components of this product are approved and listed on the Canadian Domestic

2.1 Classification of the substance or mixture

Will not occur. CONDITIONS TO AVOID: Extremely high temperatures. INCOMPATIBILITY (MATERIALS TO AVOID): Avoid contact with strong oxidizing agents. HAZARDOUS DECOMPOSITION OR BY PRODUCTS: Hazardous decomposition may produce carbon dioxide and/or carbon monoxide. SECTION VII SPILL AND LEAK PROCEDURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Refer to other sections in this document. Eliminate all sources of ignition. Absorb liquid in absorbent material (1.e. dry sand or earth), then place in a chemical waste container for proper disposal. Prevent spreading to ground water. Avoid runoff into storm sewers and ditches that lead to waterways. WASTE DISPOSAL METHOD: Recycle whenever possible or destroy by liquid incineration in accordance with applicable regulations. Contaminated absorbent should be incinerated or sent to an approved landfill in accordance with Local, State, and Federal Regulations. SECTION VIII SAFE HANDLING AND USE INFORMATION RESPIRATORY PROTECTION: If TLV of the product or