AGERITE* RESIN

Appearance/Odor

Amber to cream to yellow to tan pastilles or powder. No odor. Density, at 25 deg C, Mg/cu m: 1,.,03-1, 09 Solubility in Water: Insoluble Percent Volatiles by Weight: 1.0 max. Particle Size: Powder-100% through 200 mesh sieve (* — Registered in U.S. Patent and Trademark Office) information presented herein has been compiled from sources considered to be dependable and is accurate and reliable to the best of our knowledge and belief but is not guaranteed to be so. Nothing herein is to be construed as recommending any practice or any product in violation of any patent or in violation of any law or regulation. It is the user’s responsibility to determine for himself the suitability of any material for a specific purpose and to adopt such safety precautions as D Page 2 of 4 MSDS: NEPA FIRE

SECTION 2: Hazards identification

ID SYSTEM 1 (dust 2) 2 0 Flash Point (deg C/deg F): 204/400 COC dry chemical. Extinguishing Carbon dioxide Media: may Water, foam, be ineffective on large fires. Special Firefighting Procedure: Wear positive pressure self-contained breathing apparatus during and after a fire. Unusual Fire and in the Dust presence suspended oF in air in critical proportions explosion an hazard. ignition The source following presents an apply to characteristics also, are expected apply to powder and, is reduced dust to from a powder: pastilles or if this form — Minimum oz/cu Ft explosive concentration: 0.03 — Minimum joules (dust ignition cloud) energy: 0.15 Ft psi/sec. — Maximum @ 0.1 oz/cu rate of pressure rise: 16,800 72 psig — Maximum @ 0.5 oz/cu pressure Ft of explosion: severity: 4.0 — Explosion (severe) sensitivity: Not determined - Ignition index: — Explosibility Not determined resistivity: 3.92 —- Volume x 10 +17 ohm-cm —~ National Fire Protection Association 497M rating (1986 edition): Class II, Group Standard sensitive to electrostatic discharge. Dust may Dust be is very by electrostatic discharge, electrical arcs, sparks, welding ignited open flame, or other significant heat torches, sources. Bond, ground dust control and devices properly and vent containers, conveyors, of other powder transfer or dust equipment. through Prohibit flow non-conductive use grounded, ducts or pipes, electrically etc.; only conveying product. conductive transfer lines when pneumatically well Prevent ventilated accumulation conditions, of dust (@.g.-, horizontal promptly surfaces, vacuuming spills, cleaning overhead sparks etc.) or Eliminate static ignition buildup sources such as suppression (e.g. humidification). A properly engineered explosion of product system are handled. must be considered where large amounts Association NFPA See standards such as the National Fire Protection in the Plastics 654, "Standard for

Prevention

of Dust Explosions Systems"; Industry"; NFPA 68, NFPA 69, “Explosion "Static Electricity" "Explosion and Venting Protection"; NFPA 77, other measures as other the standards as the need exists. Implement need exists. information presented herein has been compiled from sources considered to be dependable and is accurate and reliable to the best of our knowledge and belief but is not guaranteed to be so. Nothing herein is to be construed as recommending any practice or any product in violation of any patent or in violation of any law or regulation. It is the user's responsibility to determine for himself the suitability of any material for a specific purpose and to adopt such safety precautions as Page 3 of Thermal Stability: Stable Materials to Avoid: Strong oxidizing agents such as hydrogen peroxide, permanganates and perchlorates. Hazardous Polymerization: Will not occur. Hazardous Decomposition Products: Carbon monoxide, carbon dioxide, oxides of nitrogen, and aromatic and aliphatic hydrocarbons. Exposure Limits: For Product — Not established. Recommend compliance with Standard For Particulates (N.0.C.) OSHA 5S mg/cu m (respirable dust); 15 mg/cu m (total dust) ACGIH 10 mg/cu m (total dust) Effects of Overexposure: Acute: None known. Dust may cause irritation. Chronic: None known. For Product — Acute oral LDS5O (rats): 4,900 mg/kg Acute dermal LDS5O (rabbits): >20,000 mg/kg No skin or eye irritation observed in rabbits. A two year chronic feeding study in rats showed no evidence of carcinogenicity. Mouse skin painting tests were negative. Ames mutagenicity was negative. Medical Conditions Generally Aggravated By Exposure: Unknown. Avoid breathing dust. Use under well-ventilated conditions. For personal hygiene protection, wash thoroughly after handling product. Heat may cause massing of powder. Keep away from sources of heat. Store below 100 deg F (38 deg C) to maintain as free flowing powder. Keep container closed. Information presented herein has been compiled from sources considered to be dependable and is accurate and reliable to the best of our knowledge and belief but is not guaranteed to be so. Nothing herein is to be construed as recommending any practice or any product in violation of any patent or in violation of any law or regulation. It is the user’s responsibility to determine for himself the suitability of any material for a specific purpose and to adopt such safety precautions as D Page of 4 Protective Equipment: Chemical goggles. Impervious gloves for pro- longed or repeated contact. Respiratory Protection: Not typically required. If dusty conditions, NIOSH-approved dust mask. Ventilation