Note: Ingredients listed on restricted chemical lists
EC/CAS
101-68-8
Name of the chemical
4,4’-Methylenediphenyl diisocyanate
Concentration
N/A
EC/CAS
9016-87-9
Name of the chemical
4,4'-Methylendiphenyldiisocyanat tech. (Polymeres) MDI, pMDI (in Form atembarer Aerosole, A-Fraktion)
Concentration
N/A
General Information
Revision date
2017-01-25
Product name
ProKrete HD, RT, SL, UTC, CM Hardeners, KreteFill Hardener, FlexKrete
1.2.1 Relevant identified uses
Hardener ProUrea Flex Hardener, ProUrea HF Hardener
Manufacturer Name
ProREZ Coatings, LLC
Icons in SDS
Company Information
company name
ProREZ Coatings, LLC
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H315, H317, H320, H332, H334, H335, H351, H373
Hazard statements
Code
Statements
H315
Causes skin irritation
H317
May cause an allergic skin reaction
H320
Causes eye irritation
H332
Harmful if inhaled
H334
May cause allergy or asthma symptoms or breathing difficulties if inhaled
H335
May cause respiratory irritation
H351
Suspected of causing cancer
H373
May cause damage to organs through prolonged or repeated exposure
Section 2
SECTION 2: Hazards identification
OSHA Emergency Overview: DANGER - CONTAINS DIPHENYLMETHANE DIISOCYANATE (MDI) Diphenylmethane diisocyanate (CAS No. 101-68-8), commonly referred to as MDI. Inhalation of MDI mists or vapors may cause respiratory irritation, breathlessness, chest discomfort, and reduced pulmonary function. Overexposure well above the OSHA PEL may result in bronchitis, bronchial spasms and pulmonary edema. Long term exposure to MDI has been reported to cause lung damage, including reduced lung function which may be permanent. Acute or chronic overexposure to MDI may cause sensitization in some individuals resulting in an allergic respiratory reactions including wheezing, shortness of breath, and difficulty breathing.
2.1 Classification of the substance or mixture
Acute Tox. 4 (Inhalation - mist) Acute toxicity Eye Dam./Irrit. 2B Serious eye damage/eye irritation Skin Corr./Irrit. 2 Skin corrosion/irritation Skin Sens. 1B Skin sensitization Resp. Sens. 1 Respiratory sensitization Carc. 2 Carcinogenicity
2.2 Label elements
Hazardous components that must be listed on the label:
Contains
4,4’-Diphenylmethane Diisocyanate
Signal word
Danger
Hazard pictograms
ProKrete, FlexKrete, KreteFill, Urea Hardeners 1 of 8
Hazard statements
H320 Causes eye irritation. H315 Causes skin irritation. H332 Harmful if inhaled. H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. H317 May cause an allergic skin reaction. H335 May cause respiratory irritation. H351 Suspected of causing cancer. H373 May cause damage to organs (Olfactory organs) through prolonged or repeated exposure (inhalation).
Prevention
P270 Wear protective gloves/protective clothing/eye protection/face protection. P271 Use only outdoors or in a well-ventilated area. P260 Do not breathe dust/gas/mist/vapors. P201 Obtain special instructions before use. P261 Avoid breathing mist. P202 Do not handle until all safety precautions have been read and understood. P2 4 In case of inadequate ventilation ear respiratory protection. P272 Contaminated work clothing should not be allowed out of the workplace. P264 Wash with plenty of water and soap thoroughly after handling.
Response
P312 Call a POISON CENTER or doctor/physician if you feel unwell. P305+P351+P33 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P308+P311 IF exposed or concerned: Call a POISON CENTER or doctor/physician. P314 Get medical advice/attention if you feel unwell. P303+P352 IF ON SKIN (or hair): Wash with plenty of soap and water. P333+P311 If skin irritation or rash occurs: Call a POISON CENTER or doctor/physician. P362+P364 Take off contaminated clothing and wash before reuse. P332+P313 If skin irritation occurs: get medical advice/attention. P337+P311 If eye irritation persists: Call a POISON CENTER or doctor/physician. Information on MDI: Results from a lifetime inhalation study in rats indicate that MDI aerosol was carcinogenic at 6mg/m3, the highest dose tested. This is well above the recommended TLV of 5 ppb (0.05 mg/m3).Only irritation was noted at the lower concentration of 0.2 and 1 mg/m3. No birth defects or teratogenic effects were reported in a teratology study with rats exposed to 1, 4, and 12 mg/m3 polymeric MDI for 6 hr/day on days 6-15 of gestation. Embryotoxicity and fetotoxicity was reported at the top dose in the presence of maternal toxicity. Persons with history of respiratory disease or hypersensitivity should not be exposed to this product. An animal study indicated that MDI may induce respiratory hypersensitivity following dermal exposure. Medical supervision of all employees who handle or come into contact with isocyanates is recommended. Pre-employment and periodic medical examinations with respiratory function tests (FEV, FVC as a minimum) are suggested. ProKrete, FlexKrete, KreteFill, Urea Hardeners 2 of 8 Persons with asthmatic conditions, chronic bronchitis, other chronic respiratory diseases, recurrent eczema or pulmonary sensitization should be excluded from working with isocyanates. Once a person is diagnosed as having pulmonary sensitization (allergic asthma) to isocyanates, further exposure is not recommended. Contact may aggravate pulmonary disorders. General Information: This product contains no listed carcinogens according to IARC, ACGIH, NTP and/or OSHA in concentrations of 0.1 percent or greater. Prolonged contact may result in chemical burns and permanent damage. Repeated or prolonged contact causes sensitization, asthma and eczemas. Read the entire SDS for a more thorough evaluation of the hazards.