Note: Ingredients listed on restricted chemical lists
EC/CAS
68410-97-9
Name of the chemical
Distillates (petroleum), light distillate hydrotreating process, low-boiling
Concentration
≥10-≤20
EC/CAS
64742-52-5
Name of the chemical
Distillates (petroleum), hydrotreated heavy naphthenic; Base oil — unspecified (A complex combination of hydrocarbons obtained by treating a petroleum fraction with hydrogen in the presence of a catalyst. It consists of hydrocarbons having carbon numbers predominantly in the range of C20 through C50 and produces a finished oil with a viscosity of at least 19 10-6 m2.s-1 at 40 °C. It contains relatively few normal paraffins.)
Concentration
≥1.0-≤5.0
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
≤1.0
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
≤1.0
EC/CAS
14464-46-1
Name of the chemical
Cristobalit (s. u. TRGS 906)
Concentration
<1.0
General Information
Version
13
Revision date
2019-04-03
Product name
LN-930 LIQUID NAILS INTERIOR MIRROR ADHSVE AHE93012TN0
1.2.1 Relevant identified uses
Industrial applications
Manufacturer Name
PPG Industries, Inc
Emergency telephone
52 55 5559 1588, 1-800-441-9695
Icons in SDS
Company Information
company name
PPG Industries, Inc
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H225, H340, H350
Hazard statements
Code
Statements
H225
Highly flammable liquid and vapour
H340
May cause genetic defects
H350
May cause cancer
Section 2
SECTION 2: Hazards identification
Ingredient(s) with unknown acute toxicity
5.5% (Oral), 89.6% (Dermal), 43.2% (Inhalation) This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many PPG products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8).
Signal word
Danger
Hazard statements
Highly flammable liquid and vapor. May cause genetic defects. May cause cancer.
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves. Wear eye or face protection. Wear protective clothing. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Use explosion-proof electrical, ventilating, lighting and all material-handling equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Keep container tightly closed.
Response
IF exposed or concerned Get medical attention. IF ON SKIN (or hair) Take off immediately all contaminated clothing. Rinse skin with water or shower.
Storage
Store locked up. Store in a well-ventilated place. Keep cool.
Disposal
Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental label elements
Sanding and grinding dusts may be harmful if inhaled. This product contains crystalline silica which can cause lung cancer or silicosis. The risk of cancer depends on the duration and level of exposure to dust from sanding surfaces or mist from spray applications. Repeated exposure to high vapor concentrations may cause irritation of the respiratory system and permanent brain and nervous system damage. Inhalation of vapor/aerosol concentrations above the recommended exposure limits causes headaches, drowsiness and nausea and may lead to unconsciousness or death. Avoid contact with skin and clothing. Wash thoroughly after handling. Emits toxic fumes when heated.
2.3 Other hazards
Prolonged or repeated contact may dry skin and cause irritation.
2.1 Classification of the substance or mixture
GERM CELL MUTAGENICITY - Category 1 CARCINOGENICITY - Category 1A Percentage of the mixture consisting of ingredient(s) of unknown toxicity: 5.5% (Oral), 89.6% (Dermal), 43.2% (Inhalation) This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many PPG products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8).