Note: Ingredients listed on restricted chemical lists
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
7-13
EC/CAS
1314-13-2
Name of the chemical
Zinc oxide; C.I. 77947
Concentration
0.5-1.5
EC/CAS
111-46-6
Name of the chemical
diethyleneglycol
Concentration
0.5-1.5
EC/CAS
107-21-1
Name of the chemical
Ethane-1,2-diol
Concentration
N/A
EC/CAS
68-12-2
Name of the chemical
Dimethyl formamide; N,N-dimethylformamide (DMFa)
Concentration
N/A
EC/CAS
77-99-6
Name of the chemical
1,1,1-trimethylolpropane
Concentration
0.1-1
General Information
Version
6.07
Revision date
2025-09-08
Product name
TOP WALL
1.2.1 Relevant identified uses
Consumer applications
supplier name
PPG Canada Inc
Icons in SDS
Company Information
company name
PPG Canada Inc
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H317, H351, H361, H373
Hazard statements
Code
Statements
H317
May cause an allergic skin reaction
Section 2
SECTION 2: Hazards identification
Classification of the substance or mixture CARCINOGENICITY - Category 2 TOXIC TO REPRODUCTION - Category 2 SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2 Health Hazards Not Otherwise Classified - Category 1 This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8)
Signal word
Danger
Hazard statements
Suspected of causing cancer. Suspected of damaging fertility or the unborn child. May cause damage to organs through prolonged or repeated exposure. (kidneys) Prolonged or repeated contact may dry skin and cause irritation.
Precautionary statements
General : Keep out of reach of children. If medical advice is needed, have product container or label at hand.
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection. Do not breathe vapor.
Response
IF exposed or concerned: Get medical advice or attention. Photosensitive agents : In case of accidental eye contact, avoid direct exposure to the sun or other sources of UV light as severe irritation including burns may result. These reactions can be delayed – get medical attention if pain, irritation or blistering occurs after contact. In case of accidental skin contact, avoid direct exposure to the sun or other sources of UV light as severe irritation including burns may result. These reactions can be delayed – get medical attention if pain, irritation, rash or blistering occurs after contact.
Storage
Store locked up.
Disposal
Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental label elements
Contains isothiazolinones. May cause allergic reaction. Sanding and grinding dusts may be harmful if inhaled. Avoid contact with skin and clothing. Wash thoroughly after handling. Emits toxic fumes when heated. Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 22.8% (oral), 22.8% (dermal), 36.2% (inhalation)
2.1 Classification of the substance or mixture
CARCINOGENICITY - Category 2 substance or mixture TOXIC TO REPRODUCTION - Category 2 SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 2 Health Hazards Not Otherwise Classified - Category 1 This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8).