Note: Ingredients listed on restricted chemical lists
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
1-5
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
1-5
EC/CAS
61790-53-2
Name of the chemical
diatomaceous earth
Concentration
1-5
EC/CAS
872-50-4
Name of the chemical
N-Methyl-2-Pyrrolidone; 1-methyl-2-pyrrolidone (NMP)
Concentration
0.1-1
EC/CAS
26530-20-1
Name of the chemical
2-Octyl-2H-isothiazol-3-one
Concentration
0.1-1
General Information
Version
9
Revision date
2025-02-13
Product name
70-330 MANOR HALL PAINT/PRIMER IN ONE EXTERIOR EGGSHELL-DEEPTONEBASE
1.2.1 Relevant identified uses
Consumer applications, Professional applications, Used by spraying
supplier name
PPG Architectural Coatings Canada, Inc
Emergency telephone
1-800-441-9695
Icons in SDS
Company Information
company name
PPG Architectural Coatings Canada, Inc
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H317, H350, H360, H372
Hazard statements
Code
Statements
H317
May cause an allergic skin reaction
Section 2
SECTION 2: Hazards identification
Classification of the substance or mixture SKIN SENSITIZATION - Category 1A CARCINOGENICITY - Category 1A TOXIC TO REPRODUCTION - Category 1B SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8)
2.2 Label elements
BASE
Signal word
Danger
Hazard statements
May cause an allergic skin reaction. May cause cancer. May damage fertility or the unborn child. Causes damage to organs through prolonged or repeated exposure.
Precautionary statements
General : Keep out of reach of children. If medical advice is needed, have product container or label at hand.
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing and eye or face protection. Do not breathe vapor. Do not eat, drink or smoke when using this product. Wash thoroughly after handling.
Response
IF exposed or concerned Get medical advice or attention. IF ON SKIN Wash with plenty of water. If skin irritation or rash occurs: Get medical advice or attention. Take off contaminated clothing and wash it before reuse.
Storage
Store locked up.
Disposal
Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental label elements
Contains isothiazolinones. May cause allergic reaction. Sanding and grinding dusts may be harmful if inhaled. This product contains crystalline silica which can cause lung cancer or silicosis. The risk of cancer depends on the duration and level of exposure to dust from sanding surfaces or mist from spray applications. Emits toxic fumes when heated.
Ingredient(s) with unknown acute toxicity
33% (oral), 33% (dermal), 33% (inhalation)
Other hazards which do not result in classification
None known.
2.1 Classification of the substance or mixture
SKIN SENSITIZATION - Category 1A substance or mixture CARCINOGENICITY - Category 1A TOXIC TO REPRODUCTION - Category 1B SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 This product contains TiO2 which has been classified as a GHS Carcinogen Category 2 based on its IARC 2B classification. For many products, TiO2 is utilized as a raw material in a liquid coating formulation. In this case, the TiO2 particles are bound in a matrix with no meaningful potential for human exposure to unbound particles of TiO2 when the product is applied with a brush or roller. Sanding the coating surface or mist from spray applications may be harmful depending on the duration and level of exposure and require the use of appropriate personal protective equipment and/or engineering controls (see Section 8).