Thermo-Lag 3000 (95%) Part A

Appearance/Odor

Light gray viscous liquid, with solvent odor BOILING POINT (at 760 mm Hg): >232°F(111°C) (Paste) WEIGHT PER GALLON ( lb. ): 10.5±0.5 VAPOR PRESSURE (at 20C or 68F): 24 mm Hg PERCENT VOLATILES BY VOLUME: <8 % EVAPORATION RATE (ether = 1): much slower VOLATILE ORGANIC CONTENT (VOC): 0.52 lb/gal VAPOR DENSITY (Air = l): 3.2 SOLUBILITY IN WATER: very low SECTION III - INGREDIENTS AND HAZARDS TRADE NAME CAS # PERCENT OCCUPATIONAL EXPOSURE LIMITS OSHA PEL ACGIH TWA *Toluene 108-88-3 5 by wt. 200 ppm 50ppm Primary Hazard: Narcosis Bisphenol A(Epichlorohydran) 25068-38-6 31 by wt. Not Established {Reaction Product} ‡Fibrous glass, 65997-17-3 0-3 by wt. continuous filament (total dust) 15 mg/m3 10 mg/m3 (respirable dust) 5 mg/m3 Primary Hazard: Respiratory effects Acrylate Monomer 15625-89-5 9% by wt l5 mg/m3 10 mg/m3 * Indicates toxic chemicals subject to the reporting requirements of Section 313 of Title III and of 40 CFR 372 Carcinogenicity of fibrous glass: NTP: No IARC: No Z List: No OSHA Reg: No IARC categorized fibrous glass as not classifiable with respect to human carcinogenicity. Toluene Reportable Quantity: 1,000 lb. Concentration of Hazardous Substance: 5% Reportable Quantity of Product: 40,000 lb. ‡ Hazard for this material is as a dust only. This hazard is eliminated in liquid paints. Dust hazard may be applicable if dried coating is subjected to grinding and/or sanding operations. SECTION IV - FIRE AND EXPLOSION HAZARD DATA FLAMMABILITY CLASSIFICATION OSHA : Flammable Liquid, Class IC FLASH POINT : 84 °F ( 29 °C ) DOT : Flammable Liquid, Class 3 TEST METHOD: TCC FLAMMABILITY LIMITS LEL: Not Avail UEL: PRODUCT NAME: Thermo-Lag 3000 (95%) Part A EXTINGUISHING MEDIA : Foam, carbon dioxide and dry chemical. SPECIAL FIRE FIGHTING PROCEDURES : Water spray may be used to cool unruptured containers. Firefighters must use self-contained breathing apparatus with a full face piece operated in a pressure demand mode to prevent inhalation of hazardous decomposition products. Use appropriate extinguishing media to control fire. Water may cause violent frothing if sprayed directly into containers of burning liquid. UNUSUAL FIRE AND EXPLOSION HAZARDS : Keep away from heat, open flames, sparks and areas where static charge may be generated. Do not apply to hot surfaces due to possible fire and explosion risk. Sealed containers may rupture if overheated. Solvent vapors are heavier than air and may travel considerable distance to a source of ignition and flash back. HAZARDOUS DECOMPOSITION PRODUCTS : Thermal oxidative decomposition can produce toxic gases, including oxides of nitrogen, hydrocarbon fragments and carbon monoxide. SECTION V - REACTIVITY DATA STABILITY UNSTABLE CONDITIONS TO AVOID: Not applicable. STABLE X INCOMPATIBILITY (MATERIALS TO AVOID) : Strong Oxidizers, Strong Bases, Acids, Amines HAZARDOUS MAY OCCUR CONDITIONS TO AVOID : Not applicable POLYMERIZATION WILL NOT OCCUR X SECTION VI - HEALTH HAZARD DATA THRESHOLD LIMIT VALUE : See HAZARDOUS COMPONENTS list in Section III. EFFECTS OF OVEREXPOSURE : Inhalation of solvent vapors: Overexposure can cause nasal and respiratory irritation, anesthetic effects, dizziness, possible unconsciousness and asphyxiation, stupor, weakness, fatigue, headache and nausea. Inhalation of free pigment dust: Overexposure can cause coughing wheezing, shortness of breath, restricted nasal passages and lung injury. Eyes: Direct contact with product may result in eye irritation. Skin: Prolonged or repeated contact with product may cause skin irritation. Swallowing: Gastrointestinal irritation, nausea, vomiting, diarrhea, death, aspiration into the lungs which can be fatal. CHRONIC (LONG TERM, CUMULATIVE): Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the vapors may be harmful or fatal. PRIMARY ROUTES OF ENTRY: Eyes, Dermal and Inhalation