Enamel Plus HFO / Flow / Stain Flow / Glass connector

Hazard statements

not applicable Information concerning to particular hazards to man and environment: The product does not have to be labelled due to the calculation procedure of the “General Classification guideline for preparations of the EU” in the latest valid version

Classification system

The classification is according to the latest editions of the EU lists, and extended by company and literature data General information: No special measures required After inhalation: Supply fresh air; consult doctor in case of complaints After skin contact: Immediately wash with soap and water and rinse thoroughly If skin irritation continues, consult a doctor After eye contact: Rinse opened eye for several minutes under running water. Then consult a doctor After swallowing: Do not induce vomiting; call for medical help immediately Suitable extinguishing agents: Water haze, foam, carbon dioxide, fire-extinguishing powder Protective equipment: Wear self-contained respiratory protective device Wear fully protective suit Person-related safety precautions: Keep away from ignition sources Measures for environmental protection: Do not allow to enter sewers/surface or ground water Measures for cleaning/collecting: Pick up mechanically

Additional information

No dangerous substances are released - Handling Information for safe handling: Keep receptacles tightly sealed Information about fire – and explosion protection: Keep ignition sources away - Do not smoke. Protect against electrostatic charges The lists valid during the making were used as basis Personal protective equipment / General protective and hygienic measures Keep away from foodstuffs, beverages and feed. Avoid contact with the eyes and skin. Wash hands before breaks and at the end of work. Respiratory protection: not required Protection of hands: Protective gloves and protective skin cream. Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material: the exact break trough time has to be found out by the manufacturer of the protective gloves and has to be observed Eye protection: goggles recommended during refilling - General information Form: viscous Colour: different according to colouring Odour: Weak, characteristic - Change in condition Melting point/Melting range: undetermined Boiling point /Boiling range undetermined - Flash point: 101°C - Ignition temperature 370°C - Self-igniting Product is not self-igniting - Danger of explosion: Product does not present an explosion hazard - Density: Not determined - Solubility in/Miscibility with water: insoluble - Solvent content Organic solvents: 0.0% Thermal decomposition/Conditions to be avoided: No decomposition if used according to specifications Materials to be avoided: In the presence of radical formers (e.g. peroxides), deoxidizing substances, and/or heavy metal ions, polymerization with heat release is possible. Dangerous reactions: Photoreactive, danger of polymerization Dangerous decomposition products: No dangerous decomposition products known - Acute Toxicity: Primary irritant effect: on the skin: not determined on the eye not determined Sensitization No sensitizing effects known - Additional toxicological information: When used and handled according to specifications, the product does not have any harmful effects to our experience and the information provided to us. The product is not subject to classification according to the calculation method of the General EU Classification Guidelines for Preparations as issued in the latest version. General notes: Do not allow product to reach ground water, water course or sewage system Water hazard class 2 (German Regulation) (Self-assessment): hazardous for water. Danger to drinking water if even small quantities leak into the ground Product: Recommendation Must be specially treated adhering to official regulations Unclean packaging: Recommendation: Disposal must be made according to official regulations Packaging that may not be cleansed are to be disposed of in the same manner as the product Recommended cleansing agent: Alcohol Land transport ADR/RID (cross-border) ADR/RID class: - Maritime transport IMDG: IMDG Class: - Marine pollutant: NO Air transport ICAO-TI and IATA-DGR: ICAO/IATA Class: - Labelling according to EU guidelines: The product is not subject to identification regulations under EU Directives and the Ordinance on Hazardous Materials (German GefStoffV). Observe the general safety regulations when handling chemicals National regulations Technical instructions (air): Class III Share in %: 2.5-10 Water hazard class: Water hazard class 2 (Self-assessment) : hazardous for water

Storage

Requirements to be met by storerooms and receptacles Close container immediately after use and protect product from light incidence Information about storage in one common storage facility: Store away from foodstuffs Further information about storage conditions: Protect from heat and direct sunlight Additional information about design of technical facilities: No further data; see item 7 Ingredients with limit values that require monitoring at the workplace: The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace.

Further information

N.d. = not defined File: HFONEW5LINGUEIDFNG.5.2.DOC V:5.2 10-05 pag. 3/ 18 Enamel Plus HFO Enamel Plus HFO is a light curing radiopaque composite for direct and indirect aesthetic restorations in anterior and posterior sectors. It follows the standard ISO 4049:2000. The system includes: *1 a. Micro hybrid radiopaque light curing composite for direct and indirect restorations available in the following shades: 3 Generic Enamel G.E.1 (low value), G.E.2 (medium value), G.E.3 (high value) 4 Opalescent Enamels O.W. (white), O.B.N. (blue), O.G. (grey), O.A. (amber) 2 Intensive White Enamels I.W. (intensive white), I.M. (intensive milky) 7 Fluorescent Dentines UD1 (A1*) - UD2 (A2*) - UD3 (A3*) - UD3,5 (A3,5*) - UD4 (A4*) - UD5 (IR5) - UD6 (IR6) Available on request: B1* - B2* - B3* - B4* - IY5 - C1* - C2* - C3* - C4* - IG5 - D3* Enamels and dentines have different characteristics of fluorescence.