Note: Ingredients listed on restricted chemical lists
EC/CAS
7732-18-5
Name of the chemical
Water, distilled, conductivity or of similar purity H2O
Concentration
15-40 10-30
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
1-5
EC/CAS
25322-69-4
Name of the chemical
polypropyleneglycol
Concentration
1-5
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
0.1-1
EC/CAS
119-61-9
Name of the chemical
Benzophenon (2022/692)
Concentration
0.1-1
General Information
Revision date
2018-11-26
Product name
ArmorWall VP Structural Insulated Sheathing with Vapor Permeable Coating for Interior/Exterior wall assembly
supplier name
Manufacturing and Distribution
Icons in SDS
Company Information
company name
Max-Life LLC dba MaxLife Industries
e-mail address of the competent person responsible for the Safety Data Sheet
cs@maxlifeindustries.com
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H320, H335
Hazard statements
Code
Statements
H320
Causes eye irritation
H335
May cause respiratory irritation
Section 2
SECTION 2: Hazards identification
Classification (GHS-US) 2.1 - Urethane Insulation Component Classification of the Substance Mixture Classification (GHS-US) Skin Irritation Category 4 Eye Irritation Category 3
2.2 Label elements
GHS-US Labeling Eyes Dust and chip form - irritation hazard. Inhalation Dust and chip form - No hazard. Skin Fiberglass mesh may cause itching/irritation when cut. Ingestion No Known hazard. Carc. Not classified as carcinogen. No known toxicity effects. Emergency Overview Prolonged exposure to dust while cutting may be irritating to eyes, nose, and throat. Score and snap generates less dust. GHS-US Labeling Section continued from page 1 Appearance Viscous Physical State Liquid Odor Slight Ammonia
Hazard statements
H320 - Dust may cause eye irritation. H335 - Dust may cause respiratory irritation. H350 - May cause cancer 2.3 - Vapor Permeable Coating Component
Precautionary statements
P260 - Do not breathe dust. P282 - Wear protective gloves/eye protection/face protection. P303 - If on Skin: Wash with plenty of soap and water. P305 - If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P201 - Obtain special instructions before use. P308+P313 - IF exposed or concerned: Get medical advice/attention. P405 - Store locked up P501 - Dispose of contents/container to an approved waste disposal plant
2.3 Other hazards
- Rigid foam dust from fabricating operations is an irritant and is flammable. Dust should be collected at the point of generations and stray dust should be regularly swept up. - Large amounts of rigid polyurethane foam assembled in one place, such as for processing into finished products or in storage, present a potential fire hazard. Once ignited, these foams may spread flame rapidly and produce intense heat, dense smoke, and toxic gases. Raw foam and fabricated items should be stored indoors, away from fabricating operations, and be protected by automatic sprinklers. Access aisles should be maintained between foam plies.
Ingredient(s) with unknown acute toxicity
No data available. 2.2 - Magnesium Oxide Sheathing Component 2.2.1 - Mixture Classification Carc. Not classified as carcinogen. No known toxicity effects. No data available. 2.3 - Vapor Permeable Coating Component 2.3.1 - Mixture Classification
Other hazards
No data available.
Classification (GHS-US)
Carc. Category 1A Carinogenicity
Hazard pictograms
GHS07
Signal word
Danger
Prevention
P202 - Do not handle until all safety precautions have been read and understood. P281 - Use personal protective equipment as required.
2.1 Classification of the substance or mixture
Classification (GHS-US) Skin Irritation Category 4 Eye Irritation Category 3