Note: Ingredients listed on restricted chemical lists
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
≥10-≤25
EC/CAS
123-86-4
Name of the chemical
acetic acid, butyl ester
Concentration
≤9.6
EC/CAS
14807-96-6
Name of the chemical
Talc
Concentration
≤10
EC/CAS
2530-83-8
Name of the chemical
[3-(2,3-epoxypropoxy)propyl]trimethoxy silane
Concentration
<3
EC/CAS
1333-86-4
Name of the chemical
carbon black
Concentration
≤1
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
≤0.3
General Information
Version
29.01
Revision date
2025-03-05
Product name
Tec/PRIME PLUS DTM HS Primer Surfacer
Manufacturer Name
MARTIN SENOUR PAINTS
Emergency telephone
(216) 566-2917, (800) 424-9300
Icons in SDS
Company Information
company name
MARTIN SENOUR PAINTS
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H225, H319, H350, H372
Hazard statements
Code
Statements
H225
Highly Flammable liquid and vapour
Section 2
SECTION 2: Hazards identification
Ingredient(s) with unknown acute toxicity
8.3% (oral), 9.6% (dermal), 9.6% (inhalation)
Signal word
Danger
Hazard statements
Highly flammable liquid and vapor. Causes serious eye irritation. May cause cancer. Causes damage to organs through prolonged or repeated exposure. (lungs)
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves, protective clothing, eye protection, face protection, or hearing protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not breathe vapor. Do not eat, drink or smoke when using this product. Wash thoroughly after handling.
Response
IF exposed or concerned Get medical advice or attention. IF ON SKIN (or hair) Take off immediately all contaminated clothing. Rinse skin with water. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice or attention.
Storage
Store locked up.
Disposal
Dispose of contents and container in accordance with all local, regional, national and international regulations.
Supplemental label elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which can cause permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. FOR PROFESSIONAL USE ONLY. This product must be mixed with other components before use. Before opening the packages, READ AND FOLLOW WARNING LABELS ON ALL COMPONENTS. Adequate ventilation required when sanding or abrading the dried film. If Adequate ventilation cannot be provided wear an approved particulate respirator (NIOSH approved). Follow respirator manufacturer's directions for respirator use. DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Abrading or sanding of the dry film may release Crystalline Silica which has been shown to cause lung damage and cancer under long term exposure. Please refer to the SDS for additional information. Keep out of reach of children. Do not transfer contents to other containers for storage.
2.3 Other hazards
None known.
2.1 Classification of the substance or mixture
SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A CARCINOGENICITY - Category 1A SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) - Category 1 Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 8.3% (oral), 9.6% (dermal), 9.6% (inhalation)
