EYE: Immediately flush eyes with water; remove contact

SECTION 2: Hazards identification

GHS Classification uncontaminated area.

Hazard statements

patient. H320 Causes eye irritation. SECTION 5 – FIRE-FIGHTING MEASURES

Hazard pictograms

None This material is an aqueous mixture and is considered

Signal word

non flammable in its normal state. After the water has evaporated, the remaining product residue will burn.

Precautionary statements

EXTINGUISHING MEDIA Water fog or fine spray can also P264 Wash hands thoroughly after handling. be used; do not use direct water stream-may spread fire P305+351+338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. Carbon dioxide; dry chemical media. Alcohol resistant foams (ATC type) are preferred. General purpose synthetic foams (including AFFF) or protein foams may also function but will be less effective. P337+313 HAZARDOUS DECOMPOSITION PRODUCTS Carbon If eye irritation persists seek medical attention. dioxide carbon monoxide. UNUSUAL FIRE AND EXPLOSION Violent steam SECTION 3 - PRODUCT COMPOSITION INFORMATION generation or eruption may occur upon application of water-based extinguishing agents. COMPONENT CAS # AMOUNT SPECIAL FIRE FIGHTING PROCEDURES: Wear self- Water 7732-18-5 85% contained breathing apparatus and protective clothing. Natural Seed Oil * 15% SECTION 6 – ACCIDENTAL RELEASE MEASURES * TRADE SECRET - PROPRIETARY FORMULA. Specific chemical identities are withheld as a trade secret under PERSONAL PRECAUTIONS, PROTECTIVE EQUIPMENT AND the provisions of OSHA hazard communication standard EMERGENCY PROCEDURES: Use personal protective 29 CFR 1910.1200. equipment as outlined for normal handling of this material. In the event of leakage, flooring may become slippery. ENVIRONMENTAL PRECAUTIONS: This material is not expected to pose a significant environmental hazard; however, waste materials should not be allowed to enter VAPOR PRESSURE: 17.5 mm Hg at 20 °C sewers or natural waterways. VAPOR DENSITY (AIR = 1): No data available MATERIALS FOR CONTAINMENT AND CLEAN-UP: Use a SPECIFIC GRAVITY (WATER = 1): Approx. 1.0 suitable absorbent to contain spills of this material. SOLUBILITY: Soluble Transfer collected liquid and solid waste material to PARTITION COEFFICIENT: No data available suitable containers for proper recovery or disposal. (N-OCTANOL/WATER) DECOMPOSITION TEMPERATURE: No data available SECTION 7 – HANDLING AND STORAGE VISCOSITY: No data available VOC CONTENT: No data available PRECAUTIONS FOR SAFE HANDLING: EVAPORATION RATE: No data available • Use good personal hygiene practices in accordance with (N-BUTYL ACETATE = 1) this material. • Use product only as directed. SECTION 10 – STABILITY AND REACTIVITY • Avoid contact with eyes, skin, and clothing. Please wear appropriate personal protective equipment for handling REACTIVITY: No data available. of this product as outlined in Section 8. CHEMICAL STABILITY: Stable when handled or stored • Do not ingest or inhale. under the recommended conditions. STORAGE: HAZARDOUS POLYMERIZATION: Product will not undergo • Store in accordance with good industrial practices. hazardous polymerization. SPECIAL HANDLING CONSIDERATIONS: This material has CHEMICAL INCOMPATIBILITY: This material is normally an expected shelf life of 24 months. stable and has no instabilities which will illicit dangerous products. However, the combination of elevated SECTION 8 – EXPOSURE CONTROLS AND PERSONAL temperatures with strong bases, strong acids, and/or PROTECTION MEASURES strong oxidizing agents should be avoided.

2.1 Classification of the substance or mixture

NOTICE TO PHYSICIANS: There is no specific antidote. (OSHA HCS): Eye Irritation (Category 2B) Treatment of overexposure should be directed at the control of symptoms and the clinical condition of the HAZARD STATEMENT(S): patient. H320 Causes eye irritation. SECTION 5 – FIRE-FIGHTING MEASURES PICTOGRAM(S): None This material is an aqueous mixture and is considered SIGNAL WORD: Warning non flammable in its normal state. After the water has evaporated, the remaining product residue will burn.