General Information
Revision date
2011-10-09
Product name
LUSTRAN SAN LK 273 LUB 552160
Product Synonyms
SAN
Chemical name
Thermoplastic Polymer
CAS No.
9003-54-7
Manufacturer Name
TRANSPORTATION EMERGENCY
Icons in SDS
Company Information
company name
INEOS ABS (USA) Corporation
GHS Information
Signal word
WARNING!
Hazard Codes
Hazard statements (CLP)
H315
Hazard statements
Code
Statements
H315
Causes skin irritation
Section 2
SECTION 2: Hazards identification
GHS Classification Health Environmental Physical Carcinogen Category 2 None
2.2 Label elements
WARNING! H315 Suspected of causing cancer
Prevention
P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P281 Wear personal protective equipment as required.
Response
P308+P313 IF exposed and concerned: Get medical advice.
Storage
P405 Store locked up.
Disposal
P501 Dispose of contents and container in accordance with local and national regulations.
Supplemental label elements
WARNING! May form combustible dust concentrations in air during processing. Melted product is flammable and produces intense heat and dense smoke during burning. Irritating gases and fumes may be given off during burning or thermal decomposition. May cause mechanical irritation (abrasion). Causes slipping hazard if spilled. Contact with hot material will cause thermal burns.
2.1 Classification of the substance or mixture
Health Environmental Physical Carcinogen Category 2 None Label Elements WARNING! H315 Suspected of causing cancer Prevention: P201 Obtain special instructions before use. P202 Do not handle until all safety precautions have been read and understood. P281 Wear personal protective equipment as required. Response: P308+P313 IF exposed and concerned: Get medical advice. Storage: P405 Store locked up. Disposal: P501 Dispose of contents and container in accordance with local and national regulations. Supplemental Labeling: WARNING! May form combustible dust concentrations in air during processing. Melted product is flammable and produces intense heat and dense smoke during burning. Irritating gases and fumes may be given off during burning or thermal decomposition. May cause mechanical irritation (abrasion). Causes slipping hazard if spilled. Contact with hot material will cause thermal burns. 3. Composition/Information on Ingredients Components Weight % Components CAS-No. >=1% Styrene/Acrylonitrile Copolymer 9003-54-7 <=0.25% Styrene 100-42-5 4. First Aid Measures Eye Contact: In case of eye contact, flush eyes with plenty of lukewarm water. Skin Contact: In case of contact with skin, wash affected areas with soap and water. In case of thermal burns, immediately immerse affected area in cold water. Do not attempt to remove material adhering to the skin. Get medical attention for burns. Inhalation: If exposed to gases or fumes from thermal processing, move to fresh air. Get medical attention, if irritation or other symptoms develop and persist. Ingestion: Not a likely route of exposure. If swallowed, get medical attention. 5. Fire-Fighting Measures Suitable Extinguishing Media: Water, foam, dry chemical, carbon dioxide (CO2). Special Fire Fighting Procedures: Firefighters should be equipped with self-contained breathing apparatus to protect against potentially toxic and irritating fumes. Unusual Fire/Explosion Hazards: Toxic and irritating gases and fumes may be given off during burning or thermal decomposition. Avoid generating dust. Fine dust dispersed in air in sufficient concentrations, and in the presence of an ignition source is a potential dust explosion hazard. Hazardous Combustion Products: Carbon dioxide, carbon monoxide, styrene, acrylonitrile, hydrogen cyanide, hydrocarbons. 6. Accidental Release Measures Spill and Leak Procedures: If molten, allow material to cool and place into an appropriate marked container for disposal. Dust deposits should not be allowed to accumulate on surfaces, as these may form an explosive mixture if they are released into the atmosphere in sufficient concentration. Avoid dispersal of dust in the air (i.e., removing dust from surfaces with compressed air). Non-sparking tools should be used. 7. Handling and Storage Handling Procedures: Handle in accordance with good industrial hygiene and safety practices. Wash thoroughly after handling. Avoid breathing dust. Use with adequate ventilation. Minimize dust generation and accumulation. Routine housekeeping should be instituted to ensure that dusts do not accumulate on surfaces. Pellets and pellet dust can build static electricity charges when subjected to the friction of transfer and mixing operations. Provide adequate precautions, such as electrical grounding and bonding, or inert atmospheres. Protect equipment (e.g. storage bins, conveyors, dust collectors) with explosion vents. Storage Temperature: 82°C (179.6°F) maximum Storage Period: Not established 8. Exposure Controls / Personal Protection United States Although no exposure limit has been established for this product, the OSHA PEL for Particulates not Otherwise Regulated (PNOR) of 15 mg/m3 total dust, 5 mg/m3 respirable fraction is recommended. Chemical OSHA PEL ACGIH TLV Styrene 100 ppm TWA 20 ppm TWA 200 ppm Ceiling 40 ppm STEL 600 ppm Maximum concentration (5 min in any 3 hrs) Canada Although no exposure limit has been established for this product, applicable provincial exposure limits for particles not otherwise classified/ specified are recommended. Provinces Chemical Exposure Limits Alberta; Manitoba; New Brunswick; Styrene 20 ppm TWA Newfoundland/Labrador; Northwest Territories; 40 ppm STEL Nova Scotia; Prince Edward Island British Columbia Styrene 50 ppm TWA 75 ppm STEL Nunavut; Québec; Saskatchewan Styrene 50 ppm TWA 100 ppm STEL Ontario Styrene 35 ppm TWA 100 ppm STEL Yukon Styrene 100 ppm TWA 125 ppm STEL Industrial Hygiene/Ventilation Measures: General dilution and local exhaust as necessary to control airborne vapors, mists, dusts and thermal decomposition products below appropriate occupational exposure limits. It is recommended that all dust control equipment such as local exhaust ventilation and material transport systems involved in handling this product contain explosion relief vents or an explosion suppression system or an oxygen deficient environment. Ensure that dust handling systems (such as exhaust ducts, dust collectors, vessels and processing equipment) are designed in a manner to prevent the escape of dust into the work area (i.e. there is no leakage from the equipment). Respiratory Protection: If the recommended exposure limits are exceeded a NIOSH approved particulate/organic vapor respirator appropriate for the form and concentration of the contaminants should be used. Selection and use of respiratory equipment must be in accordance with OSHA 1910.134 or other applicable regulations and good industrial hygiene practice. Hand Protection: Wear heat resistant gloves when handling molten material. Eye Protection: Safety glasses with side shields. Skin and Body Protection: No special protection required for normal handling and use. For operations where heated polymer is handled, thermally protective gloves and clothing should be worn along with appropriate eye protection. Additional Protective Measures: Employees should wash their hands and face before eating, drinking, or using tobacco products. Educate and train employees in the safe use and handling of this product. Purgings should be collected as small flat, thin shapes or thin strands to allow for rapid cooling. Precautions should be taken against autoignition of hot, thick masses of the plastic. Quench with water. Fumes or vapors emitted from the hot melted plastic during converting operations may condense on cool overhead metal surfaces or exhaust ducts. The condensate, usually in the form of a soft, grease-like semi- solid may contain substances which can be irritating or toxic. Wear rubber gloves when cleaning contaminated surfaces. Use only appropriately classified electrical equipment and powered industrial trucks where dust from product is present. 9 Physical and Chemical Properties Form: Solid Appearance: Pellets Color: Tinted, Clear Odor: Slight pH: Not applicable Boiling Point/Range: Not applicable Flash Point: 380°C (716°F) Vapor Pressure: Not applicable Lower Explosion Limit: Not established Bulk Density: 650-750 kg/m3 Upper Explosion Limit: Not established Specific Gravity: Approx. 1.06 Autoignition Temperature: 450°C (842°F) Solubility in Water: Insoluble Decomposition 260°C (500°F) Softening Point: 93°C (199.4°F) Temperature: 10. Stability and Reactivity Hazardous Reactions: Hazardous polymerization does not occur. Stability: Stable Materials to Avoid: None known Conditions to Avoid: None known Hazardous Decomposition: Thermal decomposition will generate carbon dioxide, carbon monoxide, styrene, acrylonitrile, hydrogen cyanide, hydrocarbons. 11. Toxicological Information Potential Health Effects Primary Routes of Entry: Inhalation, Skin Contact, Eye Contact Medical Conditions Aggravated by Exposure: Respiratory, eye and skin disorders. HUMAN HEALTH EFFECTS AND SYMPTOMS OF EXPOSURE Skin (Acute): Contact with heated material can cause thermal burns. Eye (Acute): May cause mechanical irritation. General Effects of Exposure Acute Effects of Exposure: Gases and fumes evolved during thermal processing or decomposition of this material may irritate the eyes, skin or respiratory tract and cause nausea, drowsiness and headache. Chronic (non-cancer) Effects of Exposure: Not expected to cause any adverse chronic health effects. Carcinogenicity: The Agency for Toxic Substances & Disease Registry concluded in their 2007 Toxicological Profile for Styrene that styrene may possibly be a weak human carcinogen. The EPA has not given a formal carcinogen classification to styrene stating “Several epidemiologic studies suggest there may be an association between styrene exposure and an increased risk of leukemia and lymphoma. However, the evidence is inconclusive due to confounding factors.” In 2011 the National Toxicology Program listed styrene as reasonably anticipated to be a human carcinogen based on limited evidence from studies in humans, sufficient evidence from studies in experimental animals, and supporting data on mechanisms of carcinogenesis. Styrene IARC – Overall evaluation: 2B Possible carcinogen IARC – Evidence of carcinogenicity in animals: Limited data IARC – Evidence of carcinogenicity in humans: Limited data NTP - Reasonably anticipated to be a human carcinogen ACGIH – A4: Not classifiable as a Human Carcinogen Toxicity Data for Styrene/Acrylonitrile Copolymer Acute Oral Toxicity: LD50 1800 mg/kg (rat), LD50 1000 mg/kg (mouse) Acute Dermal Toxicity: LD50 >2,000 mg/kg (rabbit) estimated Skin Irritation: rabbit – Draize – No skin irritation Eye Irritation: rabbit – No eye irritation Sensitization: Dermal – non-sensitizer (guinea pig maximization test (GPMT)), non-sensitizer human Other Relevant Toxicity Information: Styrene is slightly toxic to practically non-toxic in oral feeding studies (rats) and skin application studies (rabbits). Repeated inhalation studies in rats for 3 weeks reported effects suggestive of a hearing impairment. Repeated inhalation exposures produced lung irritation in guinea pigs and organ weight changes in rats. Styrene caused lung tumors in several strains of mice by inhalation and oral exposure. The evidence in rats is insufficient for reaching a conclusion concerning the carcinogenicity of styrene. There is limited evidence for the carcinogenicity of styrene in humans based on studies of workers that showed an increased mortality from or incidence of cancer of the lymphohematopoietic system and increased levels of DNA adducts and genetic damage in lymphocytes from exposed workers. However, the types of lymphohematopoietic cancer observed in excess varied across different studies and excess risk was not found in all cohorts. In standard mutagenicity tests, both positive and negative results were reported. No birth defects occurred in rats given styrene orally. Some toxic effects on the fetus were noted in a limited inhalation study using repeated high doses. Toxicity Data for Styrene Acute Oral Toxicity: LD50 1000 mg/kg (rat) Acute Inhalation Toxicity: LC50 11.8 mg/L/4 hr (rat) Acute Dermal Toxicity: LD50 >20,000 mg/kg (rabbit) Skin Irritation: rabbit – Draize – moderately irritating Eye Irritation: rabbit – Draize – severely irritating Sensitization: Dermal – non-sensitizer (guinea pig maximization test (GPMT)) Repeated Dose Toxicity 6 months, inhalation NOAEL 6.3 mg/kg (monkey, male/female, daily) 28 Days, dermal NOAEL <500 mg/kg (rat, male daily) 13 weeks, inhalation NOAEL 0.565 mg/L (rat, male/female, daily) Mutagenicity Genetic Toxicity in Vitro: Ames: negative (Salmonella typhimurium, metabolic activation with and without) Sister Chromatid Exchange: positive (human lymphocytes, metabolic activation with and without) Genetic Toxicity in Vivo: Cytogenic assay positive (rat) Drosophila SLRL test: positive (Drosophila melanogaster) Carcinogenicity Styrene was tested for carcinogenicity in rats in four gavage studies, one drinking water study and two inhalation studies. Overall, there was no reliable evidence for an increase in tumor incidence in rats in any of these studies. Inhalation exposure caused benign lung tumors (alveolar/bronchiolar adenoma) and increased the combined incidence of benign and malignant lung tumors (alveolar/bronchiolar adenoma and carcinoma) in CD-1 mice of both sexes; in females, it also increased the separate incidence of malignant lung tumors. In male B6C3F1 mice, oral exposure to styrene increased the combined incidence of benign and malignant lung tumors (alveolar/bronchiolar adenoma and carcinoma), and a positive dose-response trend was observed (NCI 1979). These findings are supported by findings of lung tumors in both sexes of O20 mice exposed to styrene (Ponomarkov and Tomatis 1978). In O20 mice, a single dose of styrene was administered to pregnant dams on gestational day 17, and pups were exposed orally once a week for 16 weeks after weaning. A significantly increased incidence and earlier onset of benign and malignant lung tumors combined (adenoma and carcinoma) occurred in mice of both sexes as early as 16 weeks after weaning. In a similar study with C57Bl mice administered a much lower dose of styrene, lung-tumor incidence was not significantly increased. A screening study by intraperitoneal administration did not find an increase in tumor incidence or multiplicity in mice. The increased risks for lymphatic and hematopoietic neoplasms observed in some human epidemiological studies are generally small, statistically unstable and are not very robust. Toxicity to Reproduction/Fertility Three generation study, oral, daily (rat, male/female) NOAEL (parental): 250 ppm, NOAEL (F1): 125 ppm, NOAEL (F2): 125 ppm No effects on reproductive parameters observed at doses tested. Other method, inhalation, daily, (rabbit female) NOAEL parental 2.6 mg/L, NOAEL (F1) 2.6 mg/L Developmental Toxicity/Teratogenicity Rat, female inhalation, gestation NOAEL (teratogenicity): >600 ppm, NOAEL (maternal) : <300 ppm. No teratogenic effects observed at doses tested. Rabbit, female, inhalation, daily, gestation, NOAEL (teratogenicity): >600 ppm, NOAEL (maternal) : >600 ppm. Fetotoxicity seen only with maternal toxicity. 12. Ecological Information Ecological Data for Styrene Biodegradation: aerobic 71% 28 d Biological Oxygen Demand (BOD): 5 days, 2.46 mg/L Chemical Oxygen Demand: 2800-2880 mg/g Theoretical Biological Oxygen Demand (ThBOD): 3.07 mg/L Bioaccumulation: Carp 13.5 BCF Acute and Chronic Toxicity to Fish LC50 9 mg/L/96 hr sheepshead minnow (cyprinodon variegatus) LC50 29 – 59.3 mg/L/96 hr fathead minnow (pimephales promelas) LC50 25 mg/L/96 hr bluegill (lepomis macrochirus) LC50 2.4 – 4.1 mg/L/96 hr rainbow trout (salmo gairdneri) Acute Toxicity to Aquatic Invertebrates EC50 4.7 – 23 mg/L/48 hr water flea (daphnia magna) Toxicity to Aquatic Plants EC50 1.4 mg/L/72 hr green algae (selenastrum capricornutum) Toxicity to Microorganisms EC50 approx. 500 mg/L/30 min activated sludge microorganisms EC50 5.5 mg/L/5 min photobacterium phosphoreum EC50 72 mg/L/16 hr pseudomonas putida 13 Disposal Considerations Waste Disposal Method Waste disposal should be in accordance with existing federal, state, provincial, and/or local environmental control laws. 14. Transportation Information Land Transport (DOT): Not Regulated Land Transport (TDG): Not Regulated Sea Transport (IMDG): Not Regulated Air Transport (ICAO/IATA): Not Regulated 15. Regulatory Information United States Federal Regulations US OSHA Hazard Communication Classification: This product is hazardous under the criteria of the Federal OSHA Hazard Communication Standard (29 CFR 1910.1200). US Toxic Substance Control Act: All the components of this product are listed on the TSCA Inventory US EPA CERCLA Hazardous Substances (40 CFR 302): Components Styrene 100-42-5 <=0.25% RQ=1000 lbs SARA Section 311/312 Hazard Categories: Chronic Health US EPA Emergency Planning and Community Right to Know Act (EPCRA) SARA Title III Section 302 Extremely Hazardous Substance (40 CFR 355, Appendix A): Components None Section 313 Toxic Chemicals (40 CFR 372.65) – Supplier Notification Required: Components Styrene 100-42-5 <=0.25% US EPA Resource Conservation and Recovery Act (RCRA) Composite List of Hazardous Wastes and Appendix VIII Hazardous Constituents (40 CFR 261): If discarded in purchased form, this product would not be a hazardous waste either by listing or by characteristic. However, under RCRA, it is the responsibility of the product user to determine at the time of disposal, whether a material containing the product or derived from the product should be classified as a hazardous waste (40 CFR 261.20-24). State Right-to-Know Information The following chemicals are specifically listed by individual states; other product specific data in other sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements you should contact the appropriate agency in your state. Massachusetts, New Jersey or Pennsylvania Right to Know Substance Lists Weight% Components CAS-No. >=1% Styrene/Acrylonitrile Copolymer 9003-54-7 New Jersey Environmental Hazardous Substance List and/or New Jersey RTK Special Hazardous Substances Lists: Weight% Components CAS-No. >=1% Styrene/Acrylonitrile Copolymer 9003-54-7 <=0.25% Styrene 100-42-5 Pennsylvania Right to Know Special Hazardous Substance List: Weight% Components CAS-No. <=0.005% Acrylonitrile 107-13-1 MA Right to Know Extraordinarily Hazardous Substance List: Weight% Components CAS-No. <=0.25% Styrene 100-42-5 <=0.005% Acrylonitrile 107-13-1 California Proposition 65: Warning! This product contains a chemical(s) known to the State of California to cause cancer. Weight% Components CAS-No. <=0.005% Acrylonitrile 107-13-1 Canadian Regulations Canadian WHMIS Classification: Class D-2-A This material has been classified in accordance with the hazard criteria of the Controlled Products Regulations, and the MSDS contains all the information required by the Controlled Products Regulations. Canadian CEPA Status: All of the components of this product are listed on the DSL. 16. Other Information Refer to NFPA 654, Standard for the Prevention of Fire and Dust Explosion from the Manufacturing, Processing, and Handling of Combustible Particulate Solids, for safe handling. NFPA 704M Rating Health 0 Flammability 1 Instability 0 Other 0=Insignificant 1=Slight 2=Moderate 3=Serious 4=Extreme HMIS Rating Health 0* Flammability 1 Physical Hazard 0 0=Minimal 1=Slight 2=Moderate 3=Serious 4=Severe * Chronic Health Hazard INEOS ABS (USA) Corporation’s method of hazard communication is comprised of Product Labels and Material Safety Data Sheets. HMIS and NFPA ratings are provided by INEOS ABS (USA) Corporation as a customer service. Contact Person: Product Safety Department Telephone: (877)-233-9227 MSDS Number: R301280 Version Date: 09/10/2011 Report Version 2.0 The information is furnished without warranty, expressed or implied. This information is believed to be accurate to the best knowledge of INEOS ABS (USA) Corporation. The information in this MSDS relates only to the specific material designated herein. INEOS ABS (USA) Corporation assumes no legal responsibility for the use or reliance upon the information in this MSDS.