Note: Ingredients listed on restricted chemical lists
EC/CAS
215-691-6/1344-28-1
Name of the chemical
aluminium oxide
Concentration
< 45
EC/CAS
215-171-9/1309-48-4
Name of the chemical
magnesium oxide
Concentration
<6
EC/CAS
238-878-4/14808-60-7
Name of the chemical
Silica, crystalline
Concentration
<10
EC/CAS
215-687-4/1344-09-8
Name of the chemical
Silicic acid, sodium salt
Concentration
< 7
EC/CAS
236-675-5/13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
<7
EC/CAS
207-439-9
Name of the chemical
Calcium carbonate
Concentration
<6
General Information
Revision date
2018-12-14
Product name
FLUX FOR SUBMERGED ARC AND ELECTROSLAG WELDING
Product name
FLUX FOR SUBMERGED ARC AND ELECTROSLAG WELDING
Identification on the label/Trade name
SWX 101, 110, 120, 130, 135, 140, 150, 160, 220, 282, 305, 330, 340, 382, HF-N
1.2.1 Relevant identified uses
FLUX FOR SUBMERGED ARC AND ELECTROSLAG WELDING
1.2.2. Uses advised against
Use only as indicated for welding operations
Emergency telephone
+1 (937) 332-4000, +1 (800) 424-9300, 1-800-424-9300, +1-703-527-3887
Icons in SDS
Company Information
company name
HOBART BROTHERS LLC
e-mail address of the competent person responsible for the Safety Data Sheet
David.Castro@HobartBrothers.com
GHS Information
Signal word
Warning
Hazard Codes
Hazard statements (CLP)
H351, H373
Hazard statements
Code
Statements
H351
Suspected of causing cancer
H373
May cause damage to organs through prolonged or repeated exposure
Section 2
SECTION 2: Hazards identification
(EC) No 1272/2008 CLASSIFICATION OF SUBSTANCE OR MIXTURE – The products described in Section 1 are classified as hazardous according to applicable GHS hazard classification criteria as
Hazard statements
H351: Suspected of causing cancer through inhalation H373: May cause damage to organs through prolonged or repeated exposure through inhalation
Precautionary statements
P201: Obtain special instructions before use. P202: Do not handle until all safety precautions have been read and understood. P260: Do not breathe dusts/fume/gas/mists/vapours/spray. P280: Wear protective gloves/protective clothing/eye protection/face protection. P308 + P313 If exposed or concerned Get medical advice/attention P314: Get medical advice/attention if you feel unwell. P405: Store locked up. P501: Dispose of contents and container in accordance with local and national regulations.
2.3 Other hazards
WARNING! - Avoid breathing welding fumes and gases, they may be dangerous to your health. Always use adequate ventilation. Always use appropriate personal protective equipment.
Principle Routes of Exposure
Respiratory System, Eyes and/or Skin ARC RAYS: The welding arc can injure eyes and burn skin. ELECTRIC SHOCK: Arc welding and associated processes can kill. See Section 8. FUMES AND GASES: Can be dangerous to your health. Welding fumes and gases cannot be classified simply. The composition and quantity of both are dependent upon the metal being welded, the process, procedures and the electrode and flux used. Most fume ingredients are present as complex oxides and compounds and not as pure metals. When the flux is consumed, the fume and gas decomposition products generated are different in percent and form from the ingredients listed in Section 3. Decomposition products of normal operation include those originating from the volatilization, reaction or oxidation, plus those from the base metal and coating, etc., of the materials shown in Section 3 of this Safety Data Sheet. Monitor for the component materials identified in the list in Section 3. Fumes from the use of this product may contain complex oxides or compounds of the following elements and molecules: amorphous silica fume, calcium oxide, fluorspar or fluorides, manganese and silica. Other reasonably expected constituents of the fume would also include complex oxides of iron, titanium, magnesium and silicon. Gaseous reaction products may include carbon monoxide and carbon dioxide. Ozone and nitrogen oxides may be formed by the radiation from the arc. . Other conditions which also influence the composition and quantity of the fumes and gases to which workers may be exposed include: coatings on the metal being welded (such as paint, plating or galvanizing), the number of welders and the volume of the work area, the quality and amount of ventilation, the position of the welder's head with respect to the fume plume, as well as the presence of contaminants in the atmosphere (such as chlorinated hydrocarbon vapors from cleaning and degreasing activities). One recommended way to determine the composition and quantity of fumes and gases to which workers are exposed is to take an air sample inside the welder's helmet if worn or in the worker's breathing zone.
2.1 Classification of the substance or mixture
required and defined in European Parliament and Council Regulations (EC) No 1907/2006 and (EC) No 1272/2008. • Specific Target Organ Toxicity (Repeated Exposure) Category 2 • Carcinogenicity Category 2