AQUENCE FB 7235 known as Adhesin A 7235

SECTION 2: Hazards identification

Classification (CLP) Classification of the substance or mixture

2.2 Label elements

(CLP) No data available. (DPD) The product is not subject to classification according to the calculation methods of the "General Classification Guideline for Preparations of the EC" as issued in the last version. MSDS-No.: 43583

2.1 Classification of the substance or mixture

Classification (CLP): No data available. Classification (DPD): No classification required. 2.2. Label elements Label elements (CLP): No data available. Label elements (DPD): The product is not subject to classification according to the calculation methods of the "General Classification Guideline for Preparations of the EC" as issued in the last version. MSDS-No.: 43583 SECTION 3: Composition/information on ingredients General chemical description: Dispersion adhesive, water-based Base substances of preparation: Ethylene-vinyl acetate copolymer Declaration of the ingredients according to CLP (EC) No 1272/2008: No data available. Declaration of ingredients according to DPD (EC) No 1999/45: Contains no dangerous substances exceeding the limits of the EU-Regulation SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Move to fresh air, consult doctor if complaint persists. Skin contact: Rinse with running water and soap. Apply replenishing cream. Change all contaminated clothing. Eye contact: Rinse immediately with plenty of running water (for 10 minutes). Seek medical attention if necessary. Ingestion: Rinse mouth, drink 1-2 glasses of water, do not induce vomiting, consult a doctor, 4,2. Most important symptoms and effects, both acute and delayed No data available. 4.3. Indication of any immediate medical attention and special treatment needed See section: Description of first aid measures SECTION 5: Firefighting measures 5.1. Extinguishing media Suitable extinguishing media: All common extinguishing agents are suitable. Extinguishing media which must not be used for safety reasons: High pressure waterjet 5.2. Special hazards arising from the substance or mixture In case of fire toxic gases can be released. 5.3. Advice for firefighters Wear self-contained breathing apparatus. Wear protective equipment. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Wear protective equipment. Danger of slipping on spilled product. MSDS-No.: 43583 6.2. Environmental precautions Do not empty into drains / surface water / ground water. 6.3. Methods and material for containment and cleaning up Remove with liquid-absorbing material (sand, peat, sawdust). Dispose of contaminated material as waste according to Section 13. 6.4. Reference to other sections See advice in section 8 SECTION 7: Handling and storage _ 7.1. Precautions for safe handling Hygiene measures: Do not eat, drink or smoke while working. Wash hands before work breaks and after finishing work. 7.2. Conditions for safe storage, including any incompatibilities Ensure good ventilation/extraction. Protect against contamination. Frost-sensitive Keep container tightly sealed and store in a frost free place. Temperatures between + 15 °C and + 25 °C 7.3. Specific end use(s) paper- and packaging adhesive SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational Exposure Limits Valid for Great Britain None Biological Exposure Indices: None 8.2. Exposure controls: Engineering controls: Ensure good ventilation/extraction. Respiratory protection: In case of aerosol formation, we recommend wearing of appropriate respiratory protection equipment with ABEK P2 filter. This recommendation should be matched to local conditions. Hand protection: Chemical-resistant protective gloves (EN 374). Suitable materials for short-term contact or splashes (recommended: at least protection index 2, corresponding to > 30 minutes permeation time as per EN 374): Polychloroprene (CR; >= 1mm thickness) or natural rubber (NR; >=1 mm thickness) Suitable materials for longer, direct contact (recommended: protection index 6, corresponding to > 480 minutes permeation time as per EN 374): Polychloroprene (CR; >= 1 mm thickness) or natural rubber (NR; >=1 mm thickness) This information is based on literature references and on information provided by glove manufacturers, or is derived by analogy with similar substances. Please note that in practice the working life of chemical-resistant protective gloves may be considerably shorter than the permeation time determined in accordance with EN 374 as a result of the many influencing factors (e.g. temperature). If signs of wear and tear are noticed then the gloves should be replaced. MSDS-No.: 43583 Eye protection: Protective goggles Skin protection: Wear protective equipment. Advices to personal protection equipment: SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Appearance dispersion liquid white Odor little intrinsic odour Odour threshold No data available / Not applicable pH 3,5- 5,5 (23 °C (73 °F); Conc.: 100 % product) Initial boiling point 100 °C (212 °F) (1.013 hPa) Flash point ; no method No flash point up to 100 °C Decomposition temperature No data available / Not applicable Vapour pressure No data available / Not applicable Density 1,1 g/em3 (20 °C (68 °F)) Bulk density No data available / Not applicable Viscosity 250 - 350 mPa.s (Brookfield; Instrument: RVT; 23 °C (73.4 °F); speed of rotation: 20 min-1; Spindle No: 2; Conce.: 100 % product) Viscosity (kinematic) No data available / Not applicable Explosive properties No data available / Not applicable Solubility (qualitative) unlimited soluble (20 °C (68 °F); Solvent: Water) Solidification temperature No data available / Not applicable Melting point No data available / Not applicable Flammability No data available / Not applicable Auto-ignition temperature No data available / Not applicable Explosive limits No data available / Not applicable Partition coefficient: n-octanol/water No data available / Not applicable Evaporation rate No data available / Not applicable Vapor density No data available / Not applicable Solid content 48,5 - 51,5 % (105 °C ) Oxidising properties No data available / Not applicable 9.2. Other information No data available / Not applicable SECTION 10: Stability and reactivity 10.1. Reactivity None if used for intended purpose. 10.2. Chemical stability Stable under recommended storage conditions, 10.3. Possibility of hazardous reactions See section reactivity 10.4. Conditions to avoid None if used for intended purpose. MSDS-No.: 43583 10.5. Incompatible materials None if used properly. 10.6. Hazardous decomposition products At higher temperatures acetic acid may be released. SECTION 11: Toxicological information 11.1. Information on toxicological effects General toxicological information: To the best of our knowledge no harmful effects are to be expected if the product is handled and used properly. SECTION 12: Ecological information General ecological information: Do not empty into drains, soil or bodies of water. 12.1. Toxicity No data available. 12.2. Persistence and degradability No data available. 12.3. Bioaccumulative potential / 12.4. Mobility in soil No data available. 12.5. Results of PBT and vPvB assessment No data available. 12.6. Other adverse effects No data available. SECTION 13: Disposal considerations 13.1. Waste treatment methods Product disposal: In consultation with the responsible local authority, must be subjected to special treatment. Waste code The valid EWC waste code numbers are source-related. The manufacturer is therefore unable to specify EWC waste codes for the articles or products used in the various sectors. The EWC codes listed are intended as a recommendation for users. We will be happy to advise you. 08 04 10 Waste adhesives and sealants other than those mentioned in 08 04 09. MSDS-No.: 43583 SECTION 14: Transport information 14.1. UN number Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR. 14.2. UN proper shipping name Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR. 14.3. Transport hazard class(es) Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR. 14.4. Packaging group Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR. 14.5. Environmental hazards Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR, 14.6. Special precautions for user Not hazardous according to RID, ADR, ADNR, IMDG, IATA-DGR. 14.7. Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code not applicable EE