Silcor LM PU Sealant Grey

GCP Australia Pty. Ltd

Revision date : 2022-12-27

SDS Library

Move your SDS library online today

Check Icon
Setup – Easy setup with our database of 16 million+ SDSs
Check Icon
Up-to-date – Your SDS get updated to latest versions.
Check Icon
Employee access – Tablets, Smartphones, or link from Corporate Intranet
Check Icon
Safety – One-click access to first aid information.
Check Icon
Labels – Generate Secondary Container Labels with just one click.
GHS08 GHS07
Health risk rating 5
Safety risk rating 1
Environmental risk rating 1

Note: Ingredients listed on restricted chemical lists

EC/CAS

6422-86-2

Name of the chemical

terephthalic acid, bis(2-ethylhexyl)ester

Concentration

-<15%

EC/CAS

1330-20-7

Name of the chemical

Xylene

Concentration

-<3%

Listed in

EC/CAS

13463-67-7

Name of the chemical

Reaction mass of titanium dioxide and silver chloride

Concentration

-<1%

General Information

Version

1.0

Revision date

2022-12-27

Product name

Silcor LM PU Sealant Grey

1.2.1 Relevant identified uses

Waterproofing

1.2.2. Uses advised against

advised against No further relevant information available

Icons in SDS

GHS07 GHS08

Company Information

company name

GCP Australia Pty. Ltd

e-mail address of the competent person responsible for the Safety Data Sheet

APMSDS@gcpat.com

GHS Information

Signal word

Danger

Hazard Codes

Hazard statements (CLP)

H302, H315, H317, H319, H332, H334, H335

Hazard statements

Code

Statements

H302

Harmful if swallowed

Section 2

SECTION 2: Hazards identification

2.1 Classification of the substance or mixture

Acute Tox. 4 H302 Harmful if swallowed. Acute Tox. 4 H332 Harmful if inhaled. Skin Irrit. 2 H315 Causes skin irritation. Eye Irritation 2A H319 Causes serious eye irritation. Resp. Sens. 1 H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled. Skin Sens. 1 H317 May cause an allergic skin reaction. STOT SE 3 H335 May cause respiratory irritation.

2.2 Label elements

The product is classified and labelled according to the Globally Harmonized System (GHS)

Hazard pictograms

      GHS07 GHS08

Signal word

Danger

Hazardous Ingredients

poly[oxy(methyl-1,2-ethanediyl)], α-hydro-ω-hydroxy-, polymer with 1,3-diisocyanatomethylbenzene

Hazard statements

Harmful if swallowed. Harmful if inhaled. Causes skin irritation. Causes serious eye irritation. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause an allergic skin reaction. May cause respiratory irritation.

Precautionary statements

Avoid breathing dust/fume/gas/mist/vapours/spray. (Contd. of page 1) Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Use only outdoors or in a well-ventilated area. Contaminated work clothing should not be allowed out of the workplace. Wear protective gloves / eye protection / face protection. Wear respiratory protection. IF SWALLOWED: Call a POISON CENTER/doctor if you feel unwell. IF ON SKIN: Wash with plenty of water. IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Rinse mouth. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention. If experiencing respiratory symptoms: Call a POISON CENTER/doctor. Take off contaminated clothing and wash it before reuse. Store in a well-ventilated place. Keep container tightly closed. Store locked up. Dispose of contents/container in accordance with local/regional/national/international regulations.

PBT Substances

Not applicable

vPvB Substances

Not applicable

SDS Library

Move your SDS library online today

Check Icon
Setup – Easy setup with our database of 16 million+ SDSs
Check Icon
Up-to-date – Your SDS get updated to latest versions.
Check Icon
Employee access – Tablets, Smartphones, or link from Corporate Intranet
Check Icon
Safety – One-click access to first aid information.
Check Icon
Labels – Generate Secondary Container Labels with just one click.