PolySWAB

Potential health effects

EYES : Not applicable. SKIN : Exposure to molten may cause thermal burns. INHALATION : Not applicable. SIGNS AND SYMPTOMS OF OVER EXPOSURE EYES Inspection method. : Irritation or redness. SKIN : Not applicable. INHALATION : Irritation of the nose, throat and respiratory tract. CHRONIC : None known CARCINOGENICITY : None known MUTAGENICITY : None known REPRODUCTIVE TOXICITY REPRODUCTIVE EFFECTS : None known

Teratogenic Effects

None known Material 1 : High Flow Polypropylene Homopolymer 1.2 COMPOSITION / INFORMATION ON IDENTIFICATION Chemical Name Wt.% CAS # Polypropylene Homopolymer > 95 9003-07-0 Stabilizers (trade secrete) < 5 1.3 FIRST AID MEASURES EYES : Flush eyes with water for 15 minutes. Get medical attention. SKIN : Molten resin - If molten material comes in contact with the skin, cool under ice water or a running stream of water. DO NOT attempt to remove the material from the skin. Removal could result in severe damage. Get medical attention. INGESTION : Not applicable. INHALATION : Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get medical attention. ANTIDOTES : Not applicable. NOTES TO PHYSICIAN : None. 1.4 FIRE - FIGHTING MEASURES FLASHPOINT AND METHOD : Not determined. FLAMMABLE LIMITS AUTOIGNITION : Not yet determined. TEMPERATURE : Not determined. EXTINGUISHING MEDIA : Use foam, carbon dioxide, or water spray when fighting fires involving this material. HAZARDOUS COMBUSTION PRODUCTS : Carbon dioxide, carbon monoxide, ketones, acrolein, aldehydes, unidentified organic compounds. EXPLOSION HAZARDS : Product as shipped is not a combustible dust. However, a combustible concentration of dust may occur when fines are suspended in air. Material 1 : High Flow Polypropylene Homopolymer FIRE FIGHTING PROCEDURES : Standard procedure for Class A fires. FIRE FIGHTING EQUIPMENT : As in any fire, water self-contained pressure demand breathing apparatus, (MSHA/NIOSH approved or equivalent) and full protective gear. SENSITIVE TO STATIC DISCHARGE : Static discharge could be an ignition source for a combustible concentration of dust. SENSITIVITY TO IMPACT : Not applicable. 1.5 ACCIDENTAL RELEASE MEASURES ENVIRONMENTAL PRECAUTIONS WATER SPILL : Keep pellets out from waterways. LAND SPILL : Not yet determined. AIR SPILL : Not yet determined. GENERAL PROCEDURES : Vacuum or sweep up material and place in a disposal container. 1.6 HANDLING AND STORAGE GENERAL PROCEDURES : Keep away from heat, sparks and flame. HANDLING : Ground and bond containers when transferring material.

Storage

This product may react with strong oxidizing agents and should not be stored near such materials. Store boxed and bags of material in areas protected with automatic sprinklers. STORAGE TEMPERATURE : 60oC (140oF) maximum. SHELF LIFE : Not yet determined. ELECTROSTATIC ACCUMULATION HAZARD : Material may accumulate static charges during transfers. Ground and bond containers when transferring material. 1.7 EXPOSURE CONTROLS PERSONAL PROTECTION NOT APPLICABLE Material 1 : High Flow Polypropylene Homopolymer 1.8 PHYSICAL AND CHEMICAL PROPERTIES PHYSICAL STATE : Solid ODOR : Slightly waxy odor APPEARANCE : Pellet COLOR : Translucent to white FREEZING POINT : Not applicable MELTING POINT : > 160oC (320oF) DENSITY : Not determined SPECIFIC GRAVITY : 0.88 TO 0.92 MOLECULAR WEIGHT : Not determined (VOC) NOTES : Not yet determined PHYSICAL STATE : None PERCENT VOLATILE : < 0.4% VAPOR PRESSURE : Not applicable BOILING POINT : Not applicable WATER SOLUBILITY : Negligible EVAPORATION RATE : Not applicable 1.9 STABILITY AND REACTIVITY NOT APPLICABLE 1.10 TOXICOLOGICAL INFORMATION NOT APPLICABLE 1.11 ECOLOGICAL INFORMATION NOT APPLICABLE 1.12 DISPOSAL CONSIDERATION NOT APPLICABLE Material 1 : High Flow Polypropylene Homopolymer 1.13 TRANSPORT INFORMATION NOT APPLICABLE 1.14 REGULATORY INFORMATION NOT APPLICABLE 1.15 OTHER INFORMATION NOT APPLICABLE Material 2 : Irgastat Conductive Polymer NOT APPILCABLE