x = Conc. %

Remarks

Observations mg/m3 ppm mg/m3 ppm AGW DEU 440 100 880 200 SKIN MAK DEU 220 50 440 100 SKIN VLA ESP 221 50 442 100 SKIN VLEP FRA 221 50 442 100 SKIN TLV GRC 435 100 650 150 GVI/KGVI HRV 221 50 442 100 SKIN VLEP ITA 221 50 442 100 SKIN TGG NLD 210 442 SKIN VLE PRT 221 50 442 100 SKIN NDS/NDSCh POL 100 200 SKIN TLV ROU 221 50 442 100 SKIN NPEL SVK 221 50 442 100 SKIN MV SVN 221 50 442 100 SKIN WEL GBR 220 50 441 100 SKIN OEL EU 221 50 442 100 SKIN TLV-ACGIH 434 100 651 150 Predicted no-effect concentration - PNEC Normal value in fresh water 0,327 mg/l Normal value in marine water 0,327 mg/l Normal value for fresh water sediment 12,46 mg/kg Normal value for marine water sediment 12,46 mg/kg Normal value for water, intermittent release 0,327 mg/l Normal value of STP microorganisms 6,58 mg/l Normal value for the terrestrial compartment 2,31 mg/kg Health - Derived no-effect level - DNEL / DMEL Effects on consumers Effects on workers

Principle Routes of Exposure

Acute Chronic Acute local Acute Chronic local systemic local systemic local systemic Oral VND 12.5 mg/kg/d Inhalation 260 65.3 442 221 mg/m3 Skin VND 125 VND 212 mg/kg/d Legend: (C) = CEILING ; INHAL = Inhalable Fraction ; RESP = Respirable Fraction ; THORA = Thoracic Fraction. VND = hazard identified but no DNEL/PNEC available ; NEA = no exposure expected ; NPI = no hazard identified. 8.2. Exposure controls As the use of adequate technical equipment must always take priority over personal protective equipment, make sure that the workplace is well aired through effective local aspiration. When choosing personal protective equipment, ask your chemical substance supplier for advice. Personal protective equipment must be CE marked, showing that it complies with applicable standards. Provide an emergency shower with face and eye wash station. HAND PROTECTION Protect hands with category III work gloves (see standard EN 374). The following should be considered when choosing work glove material: compatibility, degradation, failure time and permeability. The work gloves' resistance to chemical agents should be checked before use, as it can be unpredictable. The gloves' wear time depends on the duration and type of use. SKIN PROTECTION Wear category II professional long-sleeved overalls and safety footwear (see Regulation 2016/425 and standard EN ISO 20344). Wash body with soap and water after removing protective clothing. EYE PROTECTION Wear airtight protective goggles (see standard EN 166). RESPIRATORY PROTECTION If the threshold value (e.g. TLV-TWA) is exceeded for the substance or one of the substances present in the product, use a mask with a type A filter whose class (1, 2 or 3) must be chosen according to the limit of use concentration. (see standard EN 14387). In the presence of gases or vapours of various kinds and/or gases or vapours containing particulate (aerosol sprays, fumes, mists, etc.) combined filters are required. Respiratory protection devices must be used if the technical measures adopted are not suitable for restricting the worker's exposure to the threshold values considered. The protection provided by masks is in any case limited. If the substance considered is odourless or its olfactory threshold is higher than the corresponding TLV-TWA and in the case of an emergency, wear open-circuit compressed air breathing apparatus (in compliance with standard EN 137) or external air-intake breathing apparatus (in compliance with standard EN 138). For a correct choice of respiratory protection device, see standard EN 529. ENVIRONMENTAL EXPOSURE CONTROLS SECTION 8. Exposure controls/personal protection ... / >> The emissions generated by manufacturing processes, including those generated by ventilation equipment, should be checked to ensure compliance with environmental standards. Product residues must not be indiscriminately disposed of with waste water or by dumping in waterways.