EUTECTRODE 4099

Hazard statements (CLP)

H317, H351, H372

Code

Statements

H317

May cause an allergic skin reaction

SECTION 2: Hazards identification

EMERGENCY OVERVIEW: Welding electrodes are not normally considered hazardous as shipped or when handled. Gloves should be worn when handling to prevent cuts. Avoid inhalation of dust from these products. Skin contact may cause possible allergic reactions. Persons with a pacemaker should not go near welding or cutting operations until they have consulted their doctor and obtained information from the manufacturer of the pacemaker device. When this product is used in a welding process the most important hazards are: heat, radiation, electric shock, and welding fumes. ROUTES OF ENTRY:

Principle Routes of Exposure

is the respiratory system. Other possible routes are eyes and/or skin contact

Potential health effects

EYES: RADIATION: Arc rays from welding can injure eyes. HEAT and MOLTEN METAL can severely damage eyes. SKIN: HEAT: Spatter and molten metal can cause burn injuries ELECTRICITY: Electric shock can kill! RADIATION from the arc: Skin cancer has been reported. INGESTION: Not an expected route of entry, but if ingested product could cause serious injury. INHALATION: FUMES: Overexposure to welding fumes may result in symptoms like metal fume fever, dizziness, nausea, dryness of the nose, throat or eyes.

Acute Health Hazards

See Section 11

Health hazards

See Section 11

Medical Conditions Generally Aggravated by Exposure

Nothing found WARNING This product contains or produces a chemical known to the State of California to cause birth defects (or other reproductive harm) and cancer. (California Health & Safety Code 25249.5 et seq.) WARNING: avoid breathing welding fumes and gases; they may dangerous to your health. Always use adequate ventilation and use appropriate personal protection equipment. CARCINOGENICITY: NICKEL - is listed as being carcinogenic to humans on IARC and NTP lists, and is listed by NIOSH as being a potential occupational carcinogen (with no further categorization). MANGANESE is listed by ACGIH as Group A4: Not classifiable as a human carcinogen SILICON DIOXIDE - is listed as being carcinogenic to humans on IARC and NTP lists, and is listed by NIOSH as being a potential occupational carcinogen (with no further categorization). WELDING FUMES (not otherwise specified) are considered to be carcinogenic defined with no further categorization by NIOSH and IARC. Package Labeling: Although this product does not require a hazard warning label in all countries, we recommend that the safety advice should be observed:

Hazard pictograms

GHS07- GHS08

Contains

Nickel

R-phrase(s)

Limited evidence of carcinogenic effect May cause sensitization by skin contact Toxic: danger of serious damage to health by prolonged exposure through inhalation Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment Brazing/welding fumes and vapors may cause metal fume fever (headache, dizziness, dryness, cough, nausea, and fever) and these symptoms may appear 4-12 hours after exposure May cause irritation by prolonged inhalation of brazing/welding fumes. GHS:

Hazard categories

Respiratory/skin sensitization Skin Sens 1 Carcinogenicity: Carc. 2 Specific target organ toxicity – repeated exposure: STOT RE 1 May cause an allergic skin reaction. Suspected of causing cancer. Causes damage to organs through prolonged or repeated exposure.

Hazard statements

H317 May cause an allergic skin reaction H351 Suspected of causing cancer H372 Causes damage to organs through prolonged or repeated exposure

Precautionary statements

P285 In case of inadequate ventilation wear respiratory protection P314 Get medical advice if you do not feel well P280 Wear protective gloves/protective clothing/eye protection/face protection P202 Do not handle until all safety precautions have been read and understood P260 Do not breathe dust/fume/gas/mist/vapors/spray P501 Dispose of contents/container to waste treatment facility in accordance with local and national regulations SECTION 2 NOTES: Before using this product, contact your doctor to determine if exposure to product or use of this product will aggravate your medical conditions. ADDITIONAL LABELING INFORMATION As an article the product does not need to be labeled in accordance with EC-directives or respective national laws. Metals in massive form, alloys, mixtures containing polymers and mixtures containing elastomers do not require a label according to this Annex (Annex I GHS), if they do not present a hazard to human health by inhalation, ingestion or contact with skin or to the aquatic environment in the form in which they are placed on the market, although classified as hazardous in accordance with the criteria of this Annex. Instead, the supplier shall provide the information to downstream users or distributors by means of the SDS.