Note: Ingredients listed on restricted chemical lists
EC/CAS
7789-75-5
Name of the chemical
Calcium fluoride
Concentration
N/A
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
N/A
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
N/A
EC/CAS
232-188-7
Name of the chemical
Calcium fluoride
Concentration
N/A
EC/CAS
236-675-5
Name of the chemical
Titandioxid; [in Pulverform mit mindestens 1 % Partikel mit aerodynamischem Durchmesser ≤ 10 μm] (2020/217)
Concentration
N/A
EC/CAS
238-878-4
Name of the chemical
Quarz-A-Staub (s. u. TRGS 906)
Concentration
N/A
General Information
Product name
WELD AB-66
supplier name
ESAB AB
Emergency telephone
+46 31 509000
Icons in SDS
Company Information
company name
ESAB AB
e-mail address of the competent person responsible for the Safety Data Sheet
sdsrequest@esab.com
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H302, H332, H372
Hazard statements
Code
Statements
H302
Harmful if swallowed
Section 2
CLP CLASSIFICATION
Danger classes Causes eye irritation, Category 2B Specific Target Organ Toxicity — Repeated exposure, hazard category 1
Hazard statements
H302, H332, H372 H302 Harmful if swallowed. H332 Harmful if inhaled. H372 Causes damage to organs through prolonged or repeated exposure.
2.2 Label elements
Labelling according to Regulation (EC) No 1272/2008 Danger codes
Signal word
Danger
Precautionary statements
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337 + P313 If eye irritation persists: Get medical advice/attention. P270 Do no eat, drink or smoke when using this product. P314 Get medical advice/attention if you feel unwell. P260 Do not breathe dust/fume/gas/mist/vapours/spray. P264 Wash hands and face thoroughly after handling. P501 Dispose of contents/container to by lawful and appropriate disposal method. P330 Rinse mouth. P301 + P312 IF SWALLOWED: Call a POISON CENTER/doctor/physician if you feel unwell. P261 Avoid breathing dust/fume/gas/mist/vapours/spray. P271 Use only outdoors or in a well-ventilated area. P304 + P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P312 Call a POISON CENTER/doctor physician if you feel unwell.
Other hazards
This product contains titanium dioxide which is possibly carcinogenic. This product contains quartz, nor- mally not in an inhalable fraction. However dust from this flux both in inhalable and respirable fraction can cause silicosis and may cause cancer. Avoid eye contact or inhalation of dust from the product. Skin con- tact is normally no hazard but should be avoided to prevent possible allergic reactions. Persons with a pacemaker should not go near welding or cutting operations until they have consulted their doctor and obtained information from the manufacturer of the device. When this product is used in a welding process, the most important hazards are welding fumes, heat, radiation and electric shock. Fumes: Welding fumes are normally not a hazard with submerged arc welding, unless the arc burns through the flux bedding. Use enough flux to avoid burn-through. Overexposure to welding fumes may result in symptoms like metal fume fever, dizziness, nausea, dryness or irritation of the nose, throat or eyes. Chronic overexposure to welding fumes may affect pulmonary function. Heat: Spatter and melting metal can cause burn injuries and start fires. Radiation: Arc rays can severely damage eyes or skin. Electricity: ELECTRIC SHOCK can kill. Other Emergency Overview: Granules in varying colours. This product is normally not considered hazardous as shipped. Gloves should be worn when handling to prevent contaminating hands with product dust.
