54111, 54113, 54115, 54600

Hazard statements (CLP)

H317, H318, H341, H373

Code

Statements

H317

May cause an allergic skin reaction

SECTION 2: Hazards identification

Emergency Overview: Physical Appearance: Milky white liquid. Immediate concerns: May cause eye, skin and respiratory tract irritation. May cause asphyxiation, or brain, lung or other organ injury if inhaled, swallowed or absorbed by the skin.

Potential health effects

Eyes: Use chemical safety goggles and/or full face shield where splashing is possible. Contact lenses should not be worn when working with this material. Maintain eye wash fountain and quick-drench facilities in work areas.. Skin: Not applicable Liquid is moderately irritating to the skin. Prolonged or repeated contact can result in drying of the skin which may result in skin irritation and dermatitis (rash). Liquid Skin Absorption: may be absorbed through the skin. Ingestion: Ingestion may cause irritation and damage to mucous membranes. Inhalation: Vapors may be irritation to the nose, throat, and respiratory tract. Prolonged inhalation may cause headaches or nausea. Chronic: No chronic health concerns known. Carcinogenicity: This material is not currently known to have carcinogenic properties. Mutagenicity: This material is not known to have mutagenic effects on genetic makeup. Reproductive toxicity: Reproductive Effects: This material is not known to cause any reproductive system damage.

Teratogenic Effects

This material is not known to contain any teratogenic substances. Irritancy: This material may cause irritation to the eyes, skin and respiratory tract. Use correct PPE when handling this material.

Signal word

Danger

Hazard statements

H318. Causes serious eye damage. H317 May cause an allergic skin reaction. H341 Suspected of causing genetic defects. H373 May cuas damage to organs through prolonged or repeated exposure if swallowed.

Precautionary statements

P264 Wash thoroughly after handling. P273 Avoid release to the environment. P280 Wear Protective gloves/protective clothing/eye protection/face protection. P302 P333 IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. P352 P313 III. Composition Chemical Name C.A.S. number Weight-% POLYFUNTIONAL AZIRIDINE 64265-57-2 5% TO 10% * Toxic chemical subject to the reporting requirements of section 313 of Title III and of 40 CFR 372. Warning This product contains chemicals known to the state of California to cause cancer and birth defects or other reproductive harm." IV. First Aid Measures Eye Contact: Immediately flush eyes with plenty of water for at least 15 minutes while holding eyelids open. Seek medical aid if irritation persists. Skin Contact: Wash with soap and water. Rinse for at least 10 minutes. Remove contaminated clothing and shoes. Get medical attention if affected area burns. Immediately remove victim to fresh air. If victim is not breathing, give artificial respiration. If breathing is difficult, oxygen should be administered by qualified Inhalation: personnel. Seek immediate medical attention. Ingestion: Do not induce vomiting, and seek immediate medical attention. Do not attempt to give any liquids if victim is unconscious. Most important symptoms and effects, both acute and delayed: Symptoms: No further relevant information available. Effects: No further relevant information available. If the victim is a child, give no more that 1 glass of water and 15cc (1 tablespoon) syrup of ipecac. If symptoms such as loss of gag reflex, convulsions, or Note to physicians: unconsciousness occur before emesis, gastric lavage should be considered following intubation with a cuffed endotracheal tube. V. Fire-Fighting Measures Flash Point and Method: 487.4º F / 253.2º C Setaflash. Auto-ignition temperature: Unknown. Suitable extinguishing media: Use water fog, \"alcohol"\ foam, dry chemical, or CO2. Unsuitable extinguishing media: None Known. Fire fighting procedures: Clear the fire area of unprotected personnel. Do not enter confined fire space without full bunker gear; including a positive pressure NIOSH approved SCBA. Cool fire exposed containers with water. If water is used, fog nozzles are preferred. When heated above the flash point, this material emits flammable vapors which, when mixed with air, can burn or be explosive. Fine mists or sprays may be Unusual fire and explosion and fire hazard: flammable at temperatures below the flash point. Combustion products: Unknown. VI. Accidental Release Measure Ventilate area of leak or spill for at least 24 hours or until it has been declared safe. Stop the leak if there is no risk involved. Clean-up personnel require protective General Procedures: clothing and respiratory protection from vapors. Absorb liquid with inert material. Only specially trained or qualified personnel should handle the emergency. Environmental Precautions: Water spill: Keep material out of storm sewers and ditches which lead to waterways. Land spill: Contact applicable authorities and determine applicable regulations based on SDS information. Air release: Contact applicable authorities and determine applicable regulations based on SDS information. Personal Precautions: For non-emergency personnel: Protective equipment: Use personal protective equipment. Avoid breathing vapours, mist or gas. Ensure adequate ventilation. For personal protection see section 8. Emergency precautions: Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air. Method of cleaning up: Clean up spills immediately and dispose of waste safely. VII. Storage and Handling Procedures Avoid freezing. Avoid contact with bacteria, fungus, or other microorganisms. Keep container closed when not in use to avoid skinning and microorganism Precautions for safe handling: contamination. Do not handle without proper protective clothing and equipment. Conditions for safe storage, including KEEP OUT OF REACH OF CHILDREN! Empty containers retain product and can be dangerous. Do not pressurize, cut weld, braze, solder, drill, grind, or expose incompatibilities: such containers to heat, flame, sparks, static electricity, or other sources of ignition. Keep containers tightly sealed.