Ice-Off Windshield Spray De-Icer

Hazard statements (CLP)

H222, H280, H301+H311+H331, H361f

Code

Statements

H222

Extremely flammable aerosol

SECTION 2: Hazards identification

Physical hazards

Flammable aerosols Category + Gases under pressure Compressed gas not otherwise classified Category 1

Health hazards

Acute toxicity, oral Category 3 Acute toxicity, dermal Category 3 Acute toxicity, inhalation Category 3 Reproductive toxicity (fertility) Category 2 Specific target organ toxicity, single exposure Category 1 (central nervous system, eyes) {oral)

Environmental hazards

Not classified. Labet elements

Signal word

Danger

Hazard statements

Extremely flammable aerosol. Contains gas under pressure; may explode if heated. Static accumulating flammable liquid can become electrostatically charged even in bonded and grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion. Toxic if swallowed. Toxic in contact with skin. Toxic if inhaled. Suspected of damaging fertility. Causes damage to organs (central nervous system, eyes) by ingestion.

Prevention

Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not spray on an open flame or other ignition source. Ground and bond container and receiving equipment. These alone may be insufficient to remove static electricity. Do not pierce or burn, even after use. Do not breathe mist or vapor. Use only outdoors or in a well-ventilated area. Wash thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves/protective clothing/eye protection/face protection. Material name: Ice-Off™ Windshield Spray De-Icer SDS CANADA 75346 (Item# 1006379) Version #:01 Issue date 06-30-2017 1/9 Canada. Alberta OELs (Occupational Health & Safety Code, Schedule 1, Table 2) Components Value 9000 mg/m3. 5000 ppm methanol (CAS 67-56-1) 328 mg/m3 250 ppm 262 mg/m3 200 ppm Canada. British Columbia OELs. (Occupational Exposure Limits for Chemical Substances, Occupational Health and Safety Regulation 296/97, as amended) Components Value carbon dioxide (CAS 15000 ppm 124-38-9) 5000 pom methanol (CAS 67-56-1) 250 ppm 200 ppm Canada. Manitoba OELs (Reg. 217/2006, The Workplace Safety And Health Act) Components Value carbon dioxide (CAS 30000 ppm 124-38-9) 5000 ppm methanol (CAS 67-56-1} 250 ppm 200 ppm Canada. Ontario OELs. (Control of Exposure to Biological or Chemical Agents) Components Value carbon dioxide (CAS 30000 ppm 124-38-9) 5000 ppm methanol (CAS 67-56-1) 250 ppm 200 ppm Canada. Quebec OELs. (Ministry of Labor - Regulation Respecting the Quality of the Work Environment) Components Value carbon dioxide (CAS 54000 mg/m3 124-38-9) 30000 ppm 9000 mg/m3 5000 ppm methanol (CAS 67-56-1) 328 mg/m3 250 ppm 262 mg/m3 200 ppm Biotogical jimit values ACGIH Biological Exposure Indices Components Determinant Sampling Time methanol (CAS 67-56-1) * * . For sampling details, please see the source document. Exposure guidelines Canada - Alberta OELs: Skin designation methanol (CAS 67-56-1) Can be absorbed through the skin. Canada - British Columbia OELs: Skin designation methanol (CAS 67-56-1) Can be absorbed through the skin. Canada - Manitoba OELs: Skin designation methanol (CAS 67-56-1) Can be absorbed through the skin. Canada - Ontario OELs: Skin designation methanol (CAS 67-56-1} Can be absorbed through the skin. Material name: Ice-Off™ Windshield Spray De-Icer SDS CANADA 75346 (Item# 1006379) Version #: 01 Issue date 06-30-2017 419 Canada - Quebec OELs: Skin designation methanol (CAS 67-56-1) Can be absorbed through the skin. Canada - Saskatchewan OELs: Skin designation methanol (CAS 67-56-1) Can be absorbed through the skin. US ACGIH Threshold Limit Values: Skin designation methanol (CAS 67-56-1) Can be absorbed through the skin. Appropriate engineering Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates controls should be matched to conditions. if applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been esiablished, maintain airborne levels to an acceptable level.