General Information
Revision date
2023-12-21
Product name
Celotex TB4000, GA4000, XR4000, CW4000, Thermaclass Cavity Wall 21
1.2.1 Relevant identified uses
Thermal insulation product for buildings
1.2.2. Uses advised against
Use only for intended applications. Some uses of PIR insulation are restricted under the Building Regulations and related guidance because of its behaviour in relation to fire. When using PIR insulation products, you need to satisfy yourself that your intended use of the product meets all relevant national Building Regulations and guidance
supplier name
Celotex
Emergency telephone
+44 (0) 1473 822093
Icons in SDS
Company Information
company name
Celotex
e-mail address of the competent person responsible for the Safety Data Sheet
technicalsupport@celotex.co.uk
Section 2
SECTION 2: Hazards identification
Classification (EC 1272/2008) Classification of the substance or mixture Classification (EC 1272/2008)
Physical hazards
Not Classified
Health hazards
Not Classified
Environmental hazards
Not Classified Human health No specific health hazards known. Sharp edges and corners may cause cuts and abrasions. If dust is generated: Dust may irritate the eyes and the respiratory system. Frequent inhalation of dust over a long period of time increases the risk of developing lung diseases
Hazard statements
NC Not Classified Labelling notes As supplied, this product does not meet the requirements for labelling.
Other hazards
This product does not contain any substances classified as PBT or vPvB
2.1 Classification of the substance or mixture
Classification (EC 1272/2008) Physical hazards Not Classified Health hazards Not Classified Environmental hazards Not Classified Human health No specific health hazards known. Sharp edges and corners may cause cuts and abrasions. If dust is generated: Dust may irritate the eyes and the respiratory system. Frequent inhalation of dust over a long period of time increases the risk of developing lung diseases. 2.2. Label elements Hazard statements NC Not Classified Labelling notes As supplied, this product does not meet the requirements for labelling. 2.3. Other hazards This product does not contain any substances classified as PBT or vPvB. SECTION 3: Composition/information on ingredients 3.2. Mixtures Product description Polyisocyanurate rigid foam insulation core with a thermal conductivity of 0.022 W/m.K. (TB4000, GA4000, CW4000, XR4000) or 0.021 W/m.K (Thermaclass Cavity Wall 21) with low emissivity aluminium foil - paper - aluminium foil composite facings on both sides. The product is defined as an article [Regulation (EC) No 1907/2006, as amended]. SECTION 4: First aid measures 4.1. Description of first aid measures General information Get medical attention if any discomfort continues. Show this Safety Data Sheet to the medical personnel. Inhalation Due to the physical nature of this product, exposure by this route is unlikely. IF INHALED: Move affected person to fresh air and keep warm and at rest in a position comfortable for breathing. If in doubt, get medical attention promptly. Ingestion Due to the physical nature of this product, it is unlikely that ingestion will occur. IF SWALLOWED: Give a few small glasses of water or milk to drink. Stop if the affected person feels sick as vomiting may be dangerous. Do not induce vomiting unless under the direction of medical personnel. Never give anything by mouth to an unconscious person. If in doubt, get medical attention promptly. Skin contact Rinse with water. Remove contamination with soap and water or recognised skin cleansing agent. If in doubt, get medical attention promptly. If skin is punctured then treat as for a normal cut or wound. Apply pressure to stop bleeding and clean wound as necessary. Use appropriate dressing. Eye contact Due to the physical nature of this product, exposure by this route is unlikely. If dust has entered the eyes, proceed as follows. Remove any contact lenses and open eyelids wide apart. Rinse with water. Do not rub eye. Get medical attention if symptoms are severe or persist after washing. Protection of first aiders First aid personnel should wear appropriate protective equipment during any rescue. 4.2. Most important symptoms and effects, both acute and delayed General information No specific health hazards known. The severity of the symptoms described will vary dependent on the concentration and the length of exposure. Inhalation No specific symptoms known. If dust is generated: Dust may irritate the respiratory system. Frequent inhalation of dust over a long period of time increases the risk of developing lung diseases. Ingestion No specific symptoms known. If dust is generated: May cause irritation. May cause discomfort. Skin contact Prolonged or repeated contact with skin may cause irritation, redness and dermatitis. Sharp edges and corners may cause cuts and abrasions. Eye contact Particles in the eyes may cause irritation and smarting. 4.3. Indication of any immediate medical attention and special treatment needed Notes for the doctor Treat symptomatically. Specific treatments No special treatment required. SECTION 5: Firefighting measures 5.1. Extinguishing media Suitable extinguishing media Extinguish with alcohol-resistant foam, carbon dioxide, dry powder or water fog. Use fire- extinguishing media suitable for the surrounding fire. Unsuitable extinguishing Do not use water jet as an extinguisher, as this will spread the fire. media 5.2. Special hazards arising from the substance or mixture Specific hazards Polyisocyanurate (PIR) foam: If ignited, hydrogen cyanide (HCN) and other toxic gases may be formed. In case of a fire involving the product, firefighters shall be informed that PIR foam is involved. Hazardous combustion Thermal decomposition or combustion products may include the following substances: Toxic products gases or vapours. Carbon dioxide (CO2). Carbon monoxide (CO). Oxides of nitrogen (NOx). Hydrogen cyanide (HCN).