Note: Ingredients listed on restricted chemical lists
EC/CAS
123-86-4
Name of the chemical
acetic acid, butyl ester
Concentration
10-30%
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
10-30%
EC/CAS
108-10-1
Name of the chemical
4-methylpentan-2-one; isobutyl methyl ketone (MIBK)
Concentration
1-5%
General Information
Revision date
2025-04-11
Product name
HP ALIPHATIC URETHANE SEMI-GLOSS - DEEP BASE
1.2.1 Relevant identified uses
Industrial paint
Manufacturer Name
Benjamin Moore & Co
Emergency telephone
+1 703-741-5970, 1-800-424-9300, +1 703-527-3887
Icons in SDS
Company Information
company name
Benjamin Moore & Co., Limited
Hazard Codes
Hazard statements (CLP)
H225, H317, H319, H336, H340, H350, H373
Hazard statements
Code
Statements
H225
Highly Flammable liquid and vapour
Section 2
SECTION 2: Hazards identification
Classification This chemical is considered hazardous by the Hazardous Products Regulations (HPR: SOR/2015-17) Serious eye damage/eye irritation Category 2A Skin sensitization Category 1 Germ cell mutagenicity Category 1B Carcinogenicity Category 1A Specific target organ toxicity (single exposure) Category 3 Specific target organ toxicity (repeated exposure) Category 2 Flammable liquids Category 2 Label elements Danger Hazard statements Causes serious eye irritation May cause an allergic skin reaction May cause genetic defects May cause cancer May cause drowsiness or dizziness May cause damage to organs through prolonged or repeated exposure Highly flammable liquid and vapor Appearance liquid Odor solvent Precautionary Statements - Prevention Obtain special instructions before use Do not handle until all safety precautions have been read and understood Use personal protective equipment as required Wash face, hands and any exposed skin thoroughly after handling Contaminated work clothing should not be allowed out of the workplace Do not breathe dust/fume/gas/mist/vapors/spray Use only outdoors or in a well-ventilated area Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking Keep container tightly closed Ground and bond container and receiving equipment Use only non-sparking tools Take action to prevent static discharges Keep cool Wear protective gloves/clothing and eye/face protection Precautionary Statements - Response IF exposed or concerned: Get medical advice/attention Eyes IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do Continue rinsing If eye irritation persists: Get medical advice/attention Skin If skin irritation or rash occurs: Get medical advice/attention Wash contaminated clothing before reuse IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower Inhalation IF INHALED: Remove person to fresh air and keep comfortable for breathing Fire In case of fire: Use CO2, dry chemical, or foam for extinction Precautionary Statements - Storage Store locked up Store in a well-ventilated place. Keep container tightly closed
Precautionary statements
Disposal Dispose of contents/container to an approved waste disposal plant
Further information
No information available CAUTION: All floor coatings may become slippery when wet. Where non-skid characteristics are desired, use an appropriate anti-slip aggregate. IMPORTANT: Designed to be mixed with other components. Mixture will have hazards of all components. Before opening packages, read all warning labels. Follow all precautions.
2.1 Classification of the substance or mixture
This chemical is considered hazardous by the Hazardous Products Regulations (HPR: SOR/2015-17) Serious eye damage/eye irritation Category 2A Skin sensitization Category 1 Germ cell mutagenicity Category 1B Carcinogenicity Category 1A Specific target organ toxicity (single exposure) Category 3 Specific target organ toxicity (repeated exposure) Category 2 Flammable liquids