Note: Ingredients listed on restricted chemical lists
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
7-13%
EC/CAS
98-56-6
Name of the chemical
4-Chloro-alpha,alpha,alpha-trifluorotoluene
Concentration
7-13%
EC/CAS
123-86-4
Name of the chemical
acetic acid, butyl ester
Concentration
1-5%
EC/CAS
868-77-9
Name of the chemical
2-hydroxyethyl methacrylate
Concentration
0.1-0.25%
General Information
Revision date
2021-11-17
Product name
ALIPHATIC ACRYLIC URETHANE DTM SATIN DEEP BASE
1.2.1 Relevant identified uses
Industrial paint
Manufacturer Name
Benjamin Moore & Co
Emergency telephone
+1 703-741-5970, 1-800-424-9300, +1 703-527-3887
Icons in SDS
Company Information
company name
Benjamin Moore & Co., Limited
Hazard Codes
Hazard statements (CLP)
H226, H315, H317, H319, H335, H351
Hazard statements
Code
Statements
H226
Flammable liquid and vapour
Section 2
SECTION 2: Hazards identification
Classification This chemical is considered hazardous by the Hazardous Products Regulations (HPR: SOR/2015-17) Skin corrosion/irritation Category 2 Serious eye damage/eye irritation Category 2A Skin sensitization Category 1A Carcinogenicity Category 2 Specific target organ toxicity (single exposure) Category 3 Flammable liquids Category 3 Label elements Warning Hazard statements Causes skin irritation Causes serious eye irritation May cause an allergic skin reaction Suspected of causing cancer May cause respiratory irritation Flammable liquid and vapor Appearance liquid Odor solvent Precautionary Statements - Prevention Obtain special instructions before use Do not handle until all safety precautions have been read and understood Use personal protective equipment as required Wash face, hands and any exposed skin thoroughly after handling Avoid breathing dust/fume/gas/mist/vapors/spray Contaminated work clothing should not be allowed out of the workplace Use only outdoors or in a well-ventilated area Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking Keep container tightly closed Ground/bond container and receiving equipment Use explosion-proof electrical/ventilating/lighting/equipment Use only non-sparking tools Take precautionary measures against static discharge Keep cool Wear protective gloves/protective clothing/eye protection/face protection Precautionary Statements - Response IF exposed or concerned: Get medical advice/attention Eyes IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do Continue rinsing If eye irritation persists: Get medical advice/attention Skin If skin irritation or rash occurs: Get medical advice/attention IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower Wash contaminated clothing before reuse Inhalation IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing Fire In case of fire: Use CO2, dry chemical, or foam for extinction Precautionary Statements - Storage Store locked up Store in a well-ventilated place. Keep container tightly closed
Precautionary statements
Disposal Dispose of contents/container to an approved waste disposal plant
Further information
No information available IMPORTANT: Designed to be mixed with other components. Mixture will have hazards of all components. Before opening packages, read all warning labels. Follow all precautions. CAUTION: All floor coatings may become slippery when wet. Where non-skid characteristics are desired, use an appropriate anti-slip aggregate.
2.1 Classification of the substance or mixture
This chemical is considered hazardous by the Hazardous Products Regulations (HPR: SOR/2015-17) Skin corrosion/irritation Category 2 Serious eye damage/eye irritation Category 2A Skin sensitization Category 1A Carcinogenicity Category 2 Specific target organ toxicity (single exposure) Category 3 Flammable liquids