AVM GPL-16

Principle Routes of Exposure

Inhalation, Eye, Skin Contact

Potential health effects

and Symptoms of Over-Exposure Negligible hazard at room temperature under normal use. Eye Contact: Solid flake or dust may cause transient irritation as a result of mechanical abrasion. Skin Contact: Essentially no irritation to skin. Mechanical injury only. Hot solid may cause thermal burns. Inhalation: Exposure to dust at high concentration may cause irritation to respiratory tract Ingestion: May cause choking is swallowed.

Medical Conditions Generally Aggravated by Exposure

Overexposure: Not expected Product is generally accepted as being biologically inert. No specific antidotal treatment, symptomatic support required. Carcinogenicity: NTP: No C: No OSHA: No 6. FIRST AID MEASURES Eye Contact: Immediately flush eyes with water for at least 15 minutes. Do not rub the eyes. If Irritation or other symptoms occur, consult a physician. Skin Contact: Get medical attention for serious burns. In case of skin contact with hot product, Immediately immerse in or flush with clean, cold water. Inhalation: Remove to fresh air. Consult physician if irritation of respiratory passage occurs. Ingestion: Consult physician. Notes to Physician: No known delayed effects following single exposure. Other Instructions: None 7. EXPOSURE CONTROLS, PERSONAL PROTECTION RECOMMENDATIONS Eye Protection: Safety glasses Skin Protection: Gloves required when handling hot material Respiratory Protection: None required in normal use of product NIOSH approved dust mask recommended if dust conditions exist Engineering Control: Ventilation Requirements-General General ventilation should be sufficient. However, if operating conditions create High airborne concentrations of this material, special ventilation may be needed. If handling results in dust generation, special ventilation may be needed to ensure that Dust exposure does not exceed the OHSA PEL for nuisance dust Required Work/Hygiene Procedure: Minimize contact with skin. Do not eat, drink or smoke in work area. Wash hands Thoroughly after handling, especially before eating drinking, smoking, chewing or using restroom facility. Dusted clothing and shoes should be thoroughly cleaned Before use. Exposure Guidelines: No. COMPONENTS OSHA-PEL ACGffi-TLV 1 Polyethylene None 8. ACCIDENTAL RELEASE CONTROL MEASURES Response to Spills: Not applicable 9. HANDLING AND STORAGE Handling: Wear safety glasses during cutting and fabricating processes. Electrostatic charge may build up during handling. Grounding of equipment is recommended.

Storage

Store in a dry place and away from direct sunlight. Container Use: Keep container closed 10. STABILITY AND REACTIVITY Stability: Stable Conditions to Avoid: Strong oxidizers Hazardous Decomposition: Carbon dioxide, carbon monoxide Hazardous Polymerization: Will not occur 11. DISPOSAL CONSIDERATIONS Disposal Method: It must be disposed of in accordance with Federal, State and local environmental control regulations. Recycle/Reclaim: Recycling and reclamation of product should be encouraged where possible. 12. TRANSPORT INFORMATION DOT Shipping Name: Not listed DOT Label: Not regulated DOT Hazard Class: Not applicable UN/NA Number: Not applicable Hazard Label(s): Not applicable Hazard Placard(s): Not applicable Packing Group: Not applicable Bulk Packaging: Not applicable RQ: Not applicable Emergency Response Guide (ERG) No.: Not applicable 13. TOXICOLOGICAL INFORMATION The information provided below can be subject to misinterpretation. Therefore, it is essential the following information be interpreted by individuals trained in its evaluation. Chemical Toxicity Data Polyethylene No toxicology data available Polyethylene is not considered hazardous materials under the OHSA Hazard Communication Standard 14. ECOLOGICAL INFORMATION No data is available on the adverse effects of this product on the environment.Neither COD or BOD data are available. 15. REGULATORY INFORMATION FEDERAL REGULATORY INFORMATION Polyethylene OSHA Status: None EPA Clean Air Act Status: None EPA Clean Water Act Status: None TSCA Status: All ingredients are listed on TSCA Inventory (40 CFR710) CERCLARQ: None SARA Title III Polyethylene Section 302(i) Section 313 (ii) Section 311/312 (iii) None (i) Reportable quantity of extremely hazardous substance, Sec. 302 planning quantity, extremely hazardous substance, Sec. 302 (ii) Toxic Chemical. Sec 313 Category as required by Sec 313 (40CFR372.65C). Must be used on Toxic Release Inventory form. (iii) Hazard category for SARA Sec.311/312 reporting HI =acute health hazard, H2=chronic health hazard, P3-fire hazard, P4=sudden release of pressure hazard, PS=reactive hazard RCRA Status: If disposed of in its purchased form, this would not be a RCRA hazardous waste either by listing or by characteristic. However, under RCRA, it is the responsibility of the product used to determine at the time of disposal whether a material containing the product or derived from the product should be classified as a hazardous waste (40CFR261.20-24). OTHER REGULATORY INFORMATION The following chemicals are specifically listed by individual states; other product-specific health and safety data in other sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements, you should contact the appropriate agency in your state. State Chemical Regulation None Polyethylene None Product Name: GPL-16, GPL-16SF, GPL-16DF International None 16. OTHER INFORMATION NFPA HMIS Fire-1 Health- 0 Health-0 Flammability - 1 Reactivity-0 Reactivity - 0 Specific Hazard-None