Note: Ingredients listed on restricted chemical lists
EC/CAS
100-42-5
Name of the chemical
Styrene ( Vinyl benzene )
Concentration
N/A
General Information
Revision date
2020-02-26
Product name
Palatal A 410-01
CAS No.
100-42-5
supplier name
AOC AG
Emergency telephone
(01)(703)527-3887 [USA] (24 hour
Icons in SDS
Company Information
company name
AOC AG
e-mail address of the competent person responsible for the Safety Data Sheet
product.safety@aocresins.com
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H226, H315, H319, H335, H351, H361, H372
Hazard statements
Code
Statements
H226
Flammable liquid and vapour
Section 2
SECTION 2: Hazards identification
29 CFR 1910.1200) OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
2.1 Classification of the substance or mixture
FLAMMABLE LIQUIDS - Category 3 SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A CARCINOGENICITY - Category 2 TOXIC TO REPRODUCTION (Unborn child) - Category 2 SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract irritation) - Category 3 SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) (hearing organs) - Category 1
Signal word
Danger
Hazard statements
H226 - Flammable liquid and vapor. H319 - Causes serious eye irritation. H315 - Causes skin irritation. H361 - Suspected of damaging the unborn child. H351 - Suspected of causing cancer. H335 - May cause respiratory irritation. H372 - Causes damage to organs through prolonged or repeated exposure. (hearing organs)
Prevention
P201 - Obtain special instructions before use. P202 - Do not handle until all safety precautions have been read and understood. P280 - Wear protective gloves 4 - 8 hours (breakthrough time) Viton® (0.70 mm); < 1 hour (breakthrough time): Chloroprene , Nitril rubber (0.2 mm). Wear eye or face protection. Wear protective clothing. P210 - Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P241 - Use explosion-proof electrical, ventilating, lighting and all material-handling equipment. P242 - Use only non-sparking tools. P243 - Take precautionary measures against static discharge. P240 - Ground container and receiving equipment. P233 - Keep container tightly closed. P271 - Use only outdoors or in a well-ventilated area. P260 - Do not breathe vapor. P270 - Do not eat, drink or smoke when using this product. P264 - Wash hands thoroughly after handling.
Response
P314 - Get medical attention if you feel unwell. P308 + P313 - IF exposed or concerned: Get medical attention. P304 + P340 + P312 - IF INHALED: Remove person to fresh air and keep comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. P303 + P361 + P353 - IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. P302 + P352 + P362+P364 - IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing and wash it before reuse. P332 + P313 - If skin irritation occurs: Get medical attention. P305 + P351 + P338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337 + P313 - If eye irritation persists: Get medical attention.
Storage
P405 - Store locked up. P233 - Keep container tightly closed. P403 - Store in a well-ventilated place. P235 - Keep cool.
Disposal
P501 - Dispose of contents and container in accordance with all local, regional, national and international regulations.
2.3 Other hazards
Gas/vapour is heavier than air and may travel along the floor to a source of ignition and flash back. HMIS® IV : Health * 3 Hazardous Material Information System (U.S.A.) Flammability 3
Physical hazards
0 The PPE (Personal Protection Equipment) designation in the HMIS is provided for use by employees at supplier sites only. Other users of this product are encouraged to evaluate the hazards of the product and assign PPE that is applicable to their specific situations. Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS® ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered trademark and service mark of the American Coatings Association, Inc. The customer is responsible for determining the PPE code for this material. For more information on HMIS® Personal Protective Equipment (PPE) codes, consult the HMIS® Implementation Manual.