AMC PUREVIS

SECTION 2: Hazards identification

According to the WHS Regulations and the ADG Code. Classification of the substance or mixture

Signal word

NOT APPLICABLE Hazard statement(s) Not Applicable Precautionary statement(s) Prevention Not Applicable Precautionary statement(s) Response Not Applicable Precautionary statement(s) Storage Not Applicable

Disposal

Not Applicable

2.1 Classification of the substance or mixture

NON-HAZARDOUS CHEMICAL. NON-DANGEROUS GOODS. According to the WHS Regulations and the ADG Code. CHEMWATCH HAZARD RATINGS Min Max Flammability 1 Toxicity 0 0 = Minimum Body Contact 1 1 = Low Reactivity 1 2 = Moderate 3 = High Chronic 0 4 = Extreme Poisons Schedule Not Applicable Classification Not Applicable Label elements Hazard pictogram(s) Not Applicable SIGNAL WORD NOT APPLICABLE Hazard statement(s) Not Applicable Precautionary statement(s) Prevention Not Applicable Precautionary statement(s) Response Not Applicable Precautionary statement(s) Storage Not Applicable Precautionary statement(s) Disposal Not Applicable SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS Substances See section below for composition of Mixtures Mixtures CAS No %[weight] Name Not Available 100 Ingredients determined not to be hazardous SECTION 4 FIRST AID MEASURES Description of first aid measures If this product comes in contact with the eyes: Wash out immediately with fresh running water. Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by Eye Contact occasionally lifting the upper and lower lids. Seek medical attention without delay; if pain persists or recurs seek medical attention. Removal of contact lenses after an eye injury should only be undertaken by skilled personnel. If skin contact occurs: Immediately remove all contaminated clothing, including footwear. Skin Contact Flush skin and hair with running water (and soap if available). Seek medical attention in event of irritation. If fumes, aerosols or combustion products are inhaled remove from contaminated area. Inhalation Other measures are usually unnecessary. If swallowed do NOT induce vomiting. If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and prevent aspiration. Ingestion Observe the patient carefully. Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious. Give water to rinse out mouth, then provide liquid slowly and as much as casualty can comfortably drink. Seek medical advice. Indication of any immediate medical attention and special treatment needed Treat symptomatically. SECTION 5 FIREFIGHTING MEASURES Extinguishing media Foam. Dry chemical powder. Special hazards arising from the substrate or mixture Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition Fire Incompatibility may result Advice for firefighters Alert Fire Brigade and tell them location and nature of hazard. Fire Fighting Wear breathing apparatus plus protective gloves. Combustible. Slight fire hazard when exposed to heat or flame. Combustion products include: , carbon dioxide (CO2) Fire/Explosion Hazard , acrolein , other pyrolysis products typical of burning organic material. CARE: Water in contact with hot liquid may cause foaming and a steam explosion with wide scattering of hot oil and possible severe burns. Foaming may cause overflow of containers and may result in possible fire. HAZCHEM Not Applicable SECTION 6 ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures See section 8 Environmental precautions See section 12 Methods and material for containment and cleaning up Slippery when spilt. Minor Spills Remove all ignition sources. Clean up all spills immediately. Slippery when spilt. Major Spills Moderate hazard. Clear area of personnel and move upwind. Personal Protective Equipment advice is contained in Section 8 of the SDS. SECTION 7 HANDLING AND STORAGE Precautions for safe handling DO NOT allow clothing wet with material to stay in contact with skin Rags wet / soaked with unsaturated hydrocarbons / drying oils may auto-oxidise; generate heat and, in-time, smoulder and ignite. This is especially the case where oil-soaked materials are folded, bunched, compressed, or piled together - this allows the heat to accumulate or even accelerate the reaction Safe handling Oily cleaning rags should be collected regularly and immersed in water, or spread to dry in safe-place away from direct sunlight or stored, immersed, in solvents in suitably closed containers. Avoid all personal contact, including inhalation. Wear protective clothing when risk of exposure occurs. Store in original containers. Other information Keep containers securely sealed. Conditions for safe storage, including any incompatibilities Metal can or drum Suitable container Packaging as recommended by manufacturer. Check all containers are clearly labelled and free from leaks. Avoid contamination of water, foodstuffs, feed or seed. Storage incompatibility Avoid reaction with oxidising agents SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Control parameters OCCUPATIONAL EXPOSURE LIMITS (OEL) INGREDIENT DATA Not Available EMERGENCY LIMITS Ingredient Material name TEEL-1 TEEL-2 TEEL-3 Not Available Ingredient Original IDLH Revised IDLH Ingredients determined not Not Available to be hazardous MATERIAL DATA Exposure controls Engineering controls are used to remove a hazard or place a barrier between the worker and the hazard. Well-designed Appropriate engineering engineering controls can be highly effective in protecting workers and will typically be independent of worker interactions controls to provide this high level of protection. Personal protection Safety glasses with side shields Eye and face protection Chemical goggles. Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. Skin protection See Hand protection below Wear general protective gloves, eg. light weight rubber gloves. The selection of suitable gloves does not only depend on the material, but also on further marks of quality which vary Hands/feet protection from manufacturer to manufacturer. Where the chemical is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Body protection See Other protection below No special equipment needed when handling small quantities. Other protection OTHERWISE: Overalls. Thermal hazards Not Available Respiratory protection Cartridge respirators should never be used for emergency ingress or in areas of unknown vapour concentrations or oxygen content. The wearer must be warned to leave the contaminated area immediately on detecting any odours through the respirator. The odour may indicate that the mask is not functioning properly, that the vapour concentration is too high, or that the mask is not properly fitted. Because of these limitations, only restricted use of cartridge respirators is considered appropriate. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Information on basic physical and chemical properties Appearance Yellow liquid; mixes with water. Relative density (Water = Physical state Liquid Not Available 1) Partition coefficient Odour Not Available n-octanol / water Not Available Auto-ignition temperature Not Available Odour threshold (°C) Decomposition pH (as supplied) Not Available temperature Melting point / freezing Not Available Viscosity (cSt) point (°C) Initial boiling point and Not Available Molecular weight (g/mol) Not Applicable boiling range (°C) Flash point (°C) Not Available Taste Not Available Evaporation rate Not Available Explosive properties Not Available Flammability Not Available Oxidising properties Not Available Upper Explosive Limit Surface Tension (dyn/cm Not Available (%) or mN/m) Lower Explosive Limit Volatile Component Not Available (%) (%vol) Vapour pressure (kPa) Not Available Gas group Not Available Solubility in water (g/L) Miscible pH as a solution (1%) 7.0-9.0 Vapour density (Air = 1) Not Available VOC g/L Not Available SECTION 10 STABILITY AND REACTIVITY Reactivity See section 7 Unstable in the presence of incompatible materials. Chemical stability Product is considered stable. Possibility of hazardous See section 7 reactions Conditions to avoid See section 7 Incompatible materials See section 7 Hazardous See section 5 decomposition products SECTION 11 TOXICOLOGICAL INFORMATION Information on toxicological effects The material is not thought to produce adverse health effects or irritation of the respiratory tract (as classified by EC Directives using animal models). Nevertheless, good hygiene practice requires that exposure be kept to a minimum and that suitable control measures be used in an occupational setting. Inhaled Fine mists generated from plant/ vegetable (or more rarely from animal) oils may be hazardous. Extreme heating for prolonged periods, at high temperatures, may generate breakdown products which include acrolein and acrolein-like substances. The material has NOT been classified by EC Directives or other classification systems as "harmful by ingestion". This is Ingestion because of the lack of corroborating animal or human evidence. The material may cause skin irritation after prolonged or repeated exposure and may produce a contact dermatitis Skin Contact (nonallergic). This form of dermatitis is often characterised by skin redness (erythema) and swelling epidermis. Eye Although the liquid is not thought to be an irritant (as classified by EC Directives), direct contact with the eye may produce transient discomfort characterised by tearing or conjunctival redness (as with windburn). Long-term exposure to the product is not thought to produce chronic effects adverse to health (as classified by EC Chronic Directives using animal models); nevertheless exposure by all routes should be minimised as a matter of course. TOXICITY IRRITATION AMC PUREVIS Not Available Legend: 1. Value obtained from Europe ECHA Registered Substances - Acute toxicity 2.* Value obtained from manufacturer's SDS. Unless otherwise specified data extracted from RTECS - Register of Toxic Effect of chemical Substances Acute Toxicity Carcinogenicity Skin Irritation/Corrosion Reproductivity Serious Eye STOT - Single Exposure Damage/Irritation Respiratory or Skin STOT - Repeated sensitisation Exposure Mutagenicity Aspiration Hazard Legend: – Data available but does not fill the criteria for classification – Data available to make classification – Data Not Available to make classification SECTION 12 ECOLOGICAL INFORMATION Toxicity ENDPOINT TEST DURATION (HR) SPECIES VALUE AMC PUREVIS SOURCE Not Not Available Available Legend: Extracted from 1. IUCLID Toxicity Data 2. Europe ECHA Registered Substances - Ecotoxicological Information - Aquatic Toxicity 3. EPIWIN Suite V3.12 (QSAR) - Aquatic Toxicity Data (Estimated) 4. US EPA, Ecotox database - Aquatic Toxicity Data 5. ECETOC Aquatic Hazard Assessment Data 6. NITE (Japan) - Bioconcentration Data 7. METI (Japan) - Bioconcentration Data 8. Vendor Data DO NOT discharge into sewer or waterways. May be harmful to fauna if not disposed of according to Section 13 and legislative requirements. [AMC] Persistence and degradability Ingredient Persistence: Water/Soil Persistence: Air No Data available for all ingredients Bioaccumulative potential Ingredient Bioaccumulation No Data available for all ingredients Mobility in soil Ingredient Mobility No Data available for all ingredients SECTION 13 DISPOSAL CONSIDERATIONS Waste treatment methods Legislation addressing waste disposal requirements may differ by country, state and/ or territory. Each user must refer to laws operating in their area. Product / Packaging DO NOT allow wash water from cleaning or process equipment to enter drains. disposal It may be necessary to collect all wash water for treatment before disposal. Recycle wherever possible or consult manufacturer for recycling options. Consult State Land Waste Authority for disposal. SECTION 14 TRANSPORT INFORMATION Labels Required Marine Pollutant NO HAZCHEM Not Applicable Land transport (ADG): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS Air transport (ICAO-IATA / DGR): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS Sea transport (IMDG-Code / GGVSee): NOT REGULATED FOR TRANSPORT OF DANGEROUS GOODS Transport in bulk according to Annex II of MARPOL and the IBC code Not Applicable SECTION 15 REGULATORY INFORMATION Safety, health and environmental regulations / legislation specific for the substance or mixture National Inventory Status Australia - AICS Y Canada - DSL Y Canada - NDSL Y China - IECSC Y Europe - EINEC / ELINCS / Y NLP Japan - ENCS Y Korea - KECI Y New Zealand - NZIoC Y Philippines - PICCS Y USA - TSCA Y Y = All ingredients are on the inventory Legend: N = Not determined or one or more ingredients are not on the inventory and are not exempt from listing(see specific ingredients in brackets) SECTION 16 OTHER INFORMATION Other information Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch Classification committee using available literature references. The SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other settings. Definitions and abbreviations PC－TWA: Permissible Concentration-Time Weighted Average PC－STEL: Permissible Concentration-Short Term Exposure Limit IARC: International Agency for Research on Cancer ACGIH: American Conference of Governmental Industrial Hygienists STEL: Short Term Exposure Limit TEEL: Temporary Emergency Exposure Limit。 IDLH: Immediately Dangerous to Life or Health Concentrations OSF: Odour Safety Factor NOAEL :No Observed Adverse Effect Level LOAEL: Lowest Observed Adverse Effect Level TLV: Threshold Limit Value LOD: Limit Of Detection OTV: Odour Threshold Value BCF: BioConcentration Factors BEI: Biological Exposure Index This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written permission from CHEMWATCH. DENINU K TJE FIRST NATION BOX 279 FORT RESOLUTION NT XOE 0M0 April 18, 2018 Jacqueline Ho Mackenzie Valley Land and Water Board 7th Floor 4922 48th St. PO Box 2130 Yellowknife NT X1A 2P6 Re: MV2018C0005, MV2018L2-0003 Dear Ms. Ho, As Chief of the Deninu K'ue First Nation I am writing to give my support for Pine Point Mining Limited's application for an expanded drilling program. Because of the Exploration Agreement that we have with the Company, we are certain to receive jobs and other economic benefits in Fort Resolution as a result of this drilling activity, as well our agreement already addresses environmental monitoring and member consultation. Deninu Kue First Nation would like to withdraw the comments posted by Rosy Bjornson, IMA Coordinator, to the Comment Review system as the noted issues are not applicable to the project or have already been addressed to our satisfaction in the Exploration Agreement with the Company and in the meetings held by the Exploration Committee, and as Chief I do not want them to be discussed by the MVLWB at this time. On behalf of Deninu Kue First nation, I apologize for the confusion in our miscommunication and I encourage the Board to approve these applications without restrictive conditions or delays. Sincerely, Chief Louis Balsillie Deninu Kue First Nation Phone # (867) 394-4335/6 Fax # (867) 394-5122 Page 1 Emai l Address adminßpdkfn .ca From: Jane Groenewegen To: Julian Morse Cc: Jacqueline Ho Subject: Pine Point Mines Land Use Permit Date: Monday, April 16, 2018 3:47:53 PM Greenway Holdings is a company that has been located in Hay River for almost 40 years offering all types of accommodation services. The economic activity for the South Slave Region generated by Pine Point Mining Ltd. has been greatly felt and appreciated. Our company has provided some accommodation services to the proponents of this project and have found them to be very professional in their dealings with local service providers. Their goals associated with this project will have far reaching benefits to Hay River and surrounding communities for hopefully many years to come. Please consider this to be a letter of strong support for their Land Use Permit and Type B Water Licence. Yours truly Jane Groenewegen Owner Greenway Holdings Ltd. Sent from my iPhone Costing Scenario: Pine Point Mining Limited – Pine Point Confirmation Drilling Program - MV2018L2-0003 and MV2018C0005 Pine Point Mining Limited (PPML) submitted applications for a Type A Land Use Permit (Permit) MV2018C0005 and a Type B Water Licence (Licence) MV2018L2-0003 to the MVLWB to conduct mineral exploration at the Pine Point District. In accordance with the MVLWB Guidelines for the Closure and Reclamation of Advanced Mineral Exploration and Mine Sites in the Northwest Territories (2013) and the recent MVLWB/INAC/GNWT Guidelines for Closure and Reclamation Cost Estimates for Mines (2017), GNWT has prepared an estimate to cover the costs to close and reclaim the site, should the proponent become insolvent and abandon the site without completing closure and reclamation of the development. The GNWT has adopted the INAC (2002) Mine Site Reclamation Policy for the Northwest Territories (INAC [2002] Reclamation Policy) when evaluating a mine’s closure and reclamation plan and estimating the corresponding security deposit. The GNWT also utilizes the 2013 MVLWB/INAC Closure Guidelines when preparing its submissions to the Boards in relation to mineral exploration, confirmation drilling, mineral production and mine closure proposals. The Boards’ authority to require proponents to post and maintain security is granted under the Mackenzie Valley Resource Management Act (MVRMA, federal legislation) and the Waters Act (territorial legislation); this authority encompasses both federal and non- federal areas across the Mackenzie Valley. Subsection 11(1) of the Waters Regulations, subsection 12(1) of the Mackenzie Valley Federal Areas Water Regulations, and subsection 32(1) of the Mackenzie Valley Land Use Regulations authorize the Boards to determine the total amount of security to be posted: The Board may fix the amount of security required to be furnished by an applicant in an amount not exceeding the aggregate costs of (b) abandonment of the undertaking; (c) restoration of the site of the undertaking; and (d) any ongoing measures that may be necessary after the abandonment of the undertaking. The proposed activities by PPML include geological mapping, sampling, and diamond drilling. PPML proposes to drill up to 2,500 holes. Other proposed operations include use of heavy machinery and vehicles, clearing existing roads and cutlines, establishing and clearing drilling pads, use and storage of fuel, use of water, deposit of waste, and site restoration. PPML has applied to operate from May 1, 2018 to July 31, 2020. The GNWT has reviewed the PPML MV2018L2-0003 Water Licence application and MV2018C0005 Land Use Permit application and has assessed the scope of work by PPML for the project to be as follows: • Mobilization and demobilization of equipment in the spring (April) of 2018 and Late-Summer (July) of 2020, respectively. • PPML proposes to drill up to 2500 confirmation holes. • All drill sites (pads) will be accessed via current existing roads and trails that can be accessed from the public highway. All drilling will take place at historic drilling locations. • Clearing may be required to access the old drill hole collars, however, that clearing will be no wider than 10 m. There are no cabins or other infrastructure on the leases and claims in this application. • There currently is no camp facility associated with the work. PPML will not be utilizing a temporary or permanent camp to complete the work, as workers will be housed in local communities. • Equipment and machinery for this work will include all those listed in the Water Licence and Land Use Permit Applications, which will be stored at the site during the construction work. For the RECLAIM Estimate for the site using the RECLAIM Model (v.7), The GNWT has presumed the following: • Remediation work for this estimate pertains only to the proposed work associated with the 2018 applications. • Removal of all heavy equipment from the equipment list in the MV2018C0005 Land Use Permit Application. This includes the assumption that one (1) drilling unit and associated support equipment would be left at nine (9) induvial sites. Equipment included all vehicles that would be left on site overnight (i.e, drill rigs, dozers, etc.), regardless if it was company owned or contractor-owned. • Hazardous waste chemical volumes were estimate from Table 1 of the application and multiplied for the number of drilling sites (9). • No removal of accommodations or camp required. • Water use will only occur from April 2018 to July 2020 (27 months). • No domestic waste (i.e. sewage) will be left on site. • Removal of temporary storage tanks for the disposal of drilling waste at each of the nine (9) locations will have to be removed at the end of construction (i.e. drilling waste to be disposed on site). • Restoration work will be required at the accessed drilling pads on new undisturbed areas and re-disturbed areas, including sumps (estimated to be 15 ha total). • Demobilization of remaining unused fuel assumed to be 10% of the amount specified in the Project Description. This is based on the application requesting that on-site fuel storage to be included as part of the operation. • Post-closure site assessment monitoring rounds, commencing the following year for three (3) years. This will include inspections and monitoring to assess soil and water contamination and vegetation status. • Access via public highway. • Remediation Work crew consist of 10 labourers, work done over 30 work days. • Workers mob and demob each day by road and are housed at local communities. • Assumed 8 hour shifts. • Interim Care and Maintenance assumed to be a monthly one-day site visit for a year. • While the standard indirect cost percentages are fixed, Engineering and Project management have been assigned 3% due to lack of engineered structures as part of the project. Table 1: Terrestrial Species at Risk that May Be Encountered in the Project Area Government Recovery Strategy, Organization Action Plan or Terrestrial COSEWIC SARA with Primary Management Plan Species at Risk1 Designation Status Management posted on the Species at Responsibility2 Risk Public Registry Common Schedule 1, Recovery Strategy – Threatened ECCC Nighthawk Threatened Final Olive-sided Schedule 1, Recovery Strategy – Flycatcher Threatened ECCC Final Caribou Schedule 1, Recovery Strategy - (Boreal population) Threatened GNWT Threatened Final Schedule 1, Management Plan - Yellow Rail Special Concern Special ECCC Concern Final Schedule 1, Management Plan - Rusty Blackbird Special Concern Special GNWT Concern Final Schedule 1, Management Plan - Short-eared Owl Special Concern Special GNWT Concern Proposed Gypsy Cuckoo Endangered No Status GNWT Bumble Bee Schedule 1, Recovery Strategy - Little Brown Myotis Endangered GNWT Proposed Schedule 1, Bank Swallow Threatened ECCC Threatened Schedule 1, Barn Swallow Threatened ECCC Horned Grebe Schedule 1, (Western Special Concern Special ECCC population) Concern Red-necked Special Concern No Status ECCC Phalarope Transverse Lady Beetle Special Concern No Status GNWT Wolverine Special Concern No Status GNWT Yellow-banded Special Concern No Status GNWT Bumble Bee Notes: 1 Fisheries and Oceans Canada has responsibility for aquatic species. 2 Environment and Climate Change Canada (ECCC) has a national role to play in the conservation and recovery of Species at Risk in Canada, as well as responsibility for management of birds described in the Migratory Birds Convention Act (MBCA). Day-to-day management of terrestrial species not covered in the MBCA is the responsibility of Government of the Northwest Territories (GNWT). Populations that exist in National Parks are managed under the authority of the Parks Canada Agency.