Note: Ingredients listed on restricted chemical lists
EC/CAS
203-865-4/111-40-0
Name of the chemical
2,2'-iminodi(ethylamine)
Concentration
25-35
EC/CAS
202-859-9/100-51-6
Name of the chemical
Benzyl Alcohol
Concentration
10-15
EC/CAS
204-679-6/124-09-4
Name of the chemical
Hexamethylenediamine
Concentration
5-15
EC/CAS
202-013-9/90-72-2
Name of the chemical
2,4,6-tris(dimethylaminomethyl)phenol
Concentration
3-7
General Information
Revision date
2019-02-15
Product name
ARC 988 (Part B)
1.2.1 Relevant identified uses
ARC Polymer Composite. Repair damage caused by impact, abrasion, erosion or corrosion; rebuild worn areas; fill holes and cracks; provide abrasion resistant surfaces
supplier name
A.W. CHESTERTON COMPANY
Emergency telephone
1-800-535-5053, +1 352-323-3500
Icons in SDS
Company Information
company name
A.W. CHESTERTON COMPANY
e-mail address of the competent person responsible for the Safety Data Sheet
ProductMSDSs@chesterton.com, customer.service@chesterton.com
GHS Information
Signal word
Danger
Hazard Codes
Hazard statements (CLP)
H302+H312, H314, H317, H318, H331, H335
Hazard statements
Code
Statements
H302+H312
Harmful if swallowed or in contact with skin
Section 2
CLP CLASSIFICATION
GHS Skin corrosion, Category 1A, H314 Serious eye damage, Category 1, H318 Acute toxicity, Category 3, H331 (aerosol/mist) Acute toxicity, Category 4, H302/312 Skin sensitization, Category 1, H317 Specific target organ toxicity – single exposure, Category 3, H335
EU Classification
29 CFR 1910.1200 / WHMIS 2015 / GHS Same as section 2.1.1. 2.1.3. Australian statement of hazardous nature Hazardous according to criteria of Safe Work Australia.
Additional information
For full text of H-statements: see SECTIONS 2.2 and 16. None 2.2.2. Labelling according to 29 CFR 1910.1200 / WHMIS 2015 / GHS
2.2 Label elements
2.2.1. Labelling according to Regulation (EC) No 1272/2008 [CLP] / GHS
Signal word
Danger Same as section 2.2.1.
Hazard statements
H314 Causes severe skin burns and eye damage. H331 Toxic if inhaled. H302/312 Harmful if swallowed or in contact with skin. H317 May cause an allergic skin reaction. H335 May cause respiratory irritation. Same as section 2.2.1.
Precautionary statements
P260 Do not breathe mist. P261 Avoid breathing vapors. P280 Wear protective gloves/clothing and eye/face protection. P303/361/353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. P305/351/338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P304/340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P301/330/331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting. P310 Immediately call a POISON CENTER or doctor. P333/313 If skin irritation or rash occurs: Get medical advice/attention. P363 Wash contaminated clothing before reuse. P403/233 Store in a well-ventilated place. Keep container tightly closed. P260 Do not breathe mist. P261 Avoid breathing vapors. P264 Wash hands thoroughly after handling. P270 Do not eat, drink or smoke when using this product. P271 Use only outdoors or in a well-ventilated area. P272 Contaminated work clothing must not be allowed out of the workplace. P280 Wear protective gloves/clothing and eye/face protection. P303/361/353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. P305/351/338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P304/340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P301/330/331 IF SWALLOWED: rinse mouth. Do NOT induce vomiting. P310 Immediately call a POISON CENTER or doctor. P333/313 If skin irritation or rash occurs: Get medical advice/attention. P363 Wash contaminated clothing before reuse. P403/233 Store in a well-ventilated place. Keep container tightly closed. P405 Store locked up. P501 Dispose of contents/container to an approved waste disposal plant.
2.3 Other hazards
The safety and health hazards are detailed separately for Part A and Part B. The final cured material is considered nonhazardous. Upon machining, refer to the precautions in the safety data sheets for Part A and Part B.