438 PTFE Coating (Aerosol)

Hazard statements (CLP)

H222, H229, H280, H319, H336, H361d, H373

Code

Statements

H222

Extremely flammable aerosol

SECTION 2: Hazards identification

Classification according to WHS Classification of the substance or mixture

Signal word

Danger Danger

Hazard statements

H222 Extremely flammable aerosol. H229 Pressurized container: May burst if heated. H319 Causes serious eye irritation. H336 May cause drowsiness or dizziness. H361d Suspected of damaging the unborn child. H222 Extremely flammable aerosol. H280 Contains gas under pressure; may explode if heated. H319 Causes serious eye irritation. H336 May cause drowsiness or dizziness. H361d Suspected of damaging the unborn child. H373 May cause damage to the central nervous system through prolonged or repeated exposure by inhalation.

Precautionary statements

P201 Obtain special instructions before use. P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P211 Do not spray on an open flame or other ignition source. P251 Do not pierce or burn, even after use. P261 Avoid breathing vapours/spray. P271 Use only outdoors or in a well-ventilated area. P280 Wear protective gloves and eye/face protection. P308/313 IF exposed or concerned: Get medical advice/attention. P410/412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C. P201 Obtain special instructions before use. P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P211 Do not spray on an open flame or other ignition source. P251 Do not pierce or burn, even after use. P260 Do not breathe vapours/spray. P280 Wear protective gloves and eye/face protection. P304/340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P305/351/338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P308/313 IF exposed or concerned: Get medical advice/attention. P403 Store in a well-ventilated place. P410/412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F. P501 Dispose of contents/container to an approved waste disposal plant.

Additional information

EUH066 Repeated exposure may cause skin dryness or cracking. Repeated exposure may cause skin dryness or cracking.

2.3 Other hazards

When heated to temperatures above 260ºC (500°F), PTFE resins begin to give off vapors that may cause temporary flu-like symptoms if inhaled. Thermal decomposition leads to the formation of oxidized products containing Carbon, Fluorine and Oxygen. The ACGIH states that no exposure limit is recommended pending determination of the toxicity of the products, but air concentration should be minimal. Likewise, when using this product avoid smoking for the same reason.

2.1 Classification of the substance or mixture

2.1.1. Classification according to Regulation (EC) No 1272/2008 [CLP] Aerosol 1, H222, H229 Eye Irrit. 2, H319 STOT SE 3, H336 Repr. 2, H361d EUH066 2.1.2. Classification according to 29 CFR 1910.1200 / WHMIS 2015 Flam. Aerosol 1, H222 Press. Gas (Comp.), H280 Eye Irrit. 2, H319 STOT SE 3, H336 Repr. 2, H361d STOT RE 2, H373 (central nervous system, inhalation) 2.1.3. Classification according to WHMIS 1988 A: Compressed gases; B5: Flammable aerosols; D2A: Very toxic materials causing other effects; D2B: Toxic materials causing other effects 2.1.4. Australian statement of hazardous nature Hazardous according to criteria of Safe Work Australia. 2.1.5. Additional information For full text of H-statements: see SECTIONS 2.2 and 16.