COMPUBLEND (TM) II GENERAL PURPOSE CLEANER (Ready-to-Use)

SECTION 2: Hazards identification

OSHA 3.1 EMERGENCY OVERVIEW Specific Physical Form: Liquid Odor, Color, Grade: Clear very light blue, very mild citrus scent General Physical Form: Liquid Immediate health, physical, and environmental hazards:

Potential health effects

Eye Contact: Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing. Skin Contact: Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Flash Point Not Applicable OSHA Flammability Classification: Not Applicable 5.2 EXTINGUISHING MEDIA Non-combustible. Choose material suitable for surrounding fire. Material will not burn. 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Not applicable. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions, protective equipment and emergency procedures Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. 6.2. Environmental precautions For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Place in a closed container approved for transportation by appropriate authorities. Dispose of collected material as soon as possible. Clean-up methods Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible. Clean up residue with water. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Keep out of the reach of children. Avoid breathing of vapors, mists or spray. Avoid prolonged or repeated skin contact. Avoid eye contact with vapors, mists, or spray. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.

Storage

Store under normal warehouse conditions. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Use in a well-ventilated area. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact with vapors, mists, or spray. Wear Safety Glasses with side shields when eye contact is possible due to splashing, spraying, or misting of material. 8.2.2 Skin Protection Avoid prolonged or repeated skin contact. Gloves not normally required. If prolonged or repeated skin contact is expected, select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Butyl Rubber, Neoprene, and Nitrile Rubber. 8.2.3 Respiratory Protection Avoid breathing of vapors, mists or spray. Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. 8.2.4 Prevention of Swallowing Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. 8.3 EXPOSURE GUIDELINES Ingredient Authority Type Limit Additional Information 1-METHOXY-2-PROPANOL ACGIH TWA 100 ppm 1-METHOXY-2-PROPANOL ACGIH STEL 150 ppm 2-BUTOXYETHANOL ACGIH TWA 20 ppm 2-BUTOXYETHANOL OSHA TWA 240 mg/m3 Skin Notation* * Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye, either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption. SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL) SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Specific Physical Form: Liquid Odor, Color, Grade: Clear very light blue, very mild citrus scent General Physical Form: Liquid Flash Point Not Applicable Boiling Point Approximately 212 ºF Specific Gravity Approximately 1 [Ref Std: WATER=1] pH Approximately 8 Solubility in Water Complete Volatile Organic Compounds < 1 % [Test Method: calculated per CARB title 2] Percent volatile No Data Available VOC Less H2O & Exempt Solvents 800 - 1200 g/l Viscosity < 100 centipoise SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: 10.1 Conditions to avoid None known 10.2 Materials to avoid None known Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous decomposition products may occur as a result of oxidation, heating, or reaction with another material. SECTION 11: TOXICOLOGICAL INFORMATION Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components. SECTION 12: ECOLOGICAL INFORMATION ECOTOXICOLOGICAL INFORMATION A 3M Product Environmental Data Sheet (PED) is available. CHEMICAL FATE INFORMATION A 3M Product Environmental Data Sheet (PED) is available. SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal Method: Dispose of waste product in a facility permitted to accept chemical waste. As a disposal alternative, incinerate in an industrial or commercial facility in the presence of a combustible material. EPA Hazardous Waste Number (RCRA): Not regulated Since regulations vary, consult applicable regulations or authorities before disposal. SECTION 14:TRANSPORT INFORMATION For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: REGULATORY INFORMATION US FEDERAL REGULATIONS 311/312 Hazard Categories: Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No STATE REGULATIONS CHEMICAL INVENTORIES The components of this product are in compliance with the chemical notification requirements of TSCA. INTERNATIONAL REGULATIONS This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: OTHER INFORMATION NFPA Hazard Classification Health 1 Flammability 0 Reactivity 0 Special Hazards None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Revision Changes: Section 1: Product use information was modified. Section 1: Division name was modified. Section 16: Disclaimer (second paragraph) was modified. Section 5: Extinguishing media information was modified. Section 5: Fire fighting procedures information was modified. Section 8: Skin protection phrase was modified. Section 13: Waste disposal method information was modified. Section 14: Transportation legal text was modified. Section 15: Inventories information was modified. Section 9: Boiling point information was modified. Section 5: Flash point information was modified. Section 9: Property description for optional properties was modified. Section 9: Specific gravity information was modified. Section 9: pH information was modified. Section 9: Solubility in water text was modified. Section 9: Flash point information was modified. Section 8: Eye/face protection comment was added. Section 8: Skin protection comment was added. Section 2: Ingredient table was added. Section 8: Exposure guidelines ingredient information was added. Section 8: Exposure guideline note was added. Section 8: Exposure guidelines data source legend was added. Section 6: 6.2. Environmental precautions heading was added. Section 6: 6.1. Personal precautions, protective equipment and emergency procedures heading was added. Section 10.1 Conditions to avoid heading was added. Section 10.2 Materials to avoid heading was added. Section 16: Web address was added. Section 6: Personal precautions information was added. Section 6: Environmental procedures information was added. Section 6: Methods for cleaning up information was added. Section 10: Materials to avoid physical property was added. Section 10: Conditions to avoid physical property was added. Section 8: Hand protection information was added. Section 1: Address was added. Copyright was added. Company logo was added. Section 6: Clean-up methods heading was added. Telephone header was added. Company Telephone was added. Section 1: Emergency phone information was added. Section 1: Emergency phone information was deleted. Section 16: HMIS hazard classification heading was deleted. Section 16: HMIS hazard classification for health was deleted. Section 16: HMIS hazard classification for flammability was deleted. Section 16: HMIS hazard classification for reactivity was deleted. Section 16: HMIS hazard classification for protection was deleted. Company Logo was deleted. Copyright was deleted. Section 16: Web address heading was deleted. Section 6: Release measures information was deleted. Section 6: Release measures heading was deleted. Section 8: Eye/face protection information was deleted.