3M(TM) Scratch Remover, PN 39044, 39070, 39057

SECTION 2: Hazards identification

29 CFR 1910.1200) 3.1 EMERGENCY OVERVIEW Odor, Color, Grade: liquid, slight solvent odor General Physical Form: Liquid Immediate health, physical, and environmental hazards: Combustible liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Contains a chemical or chemicals which can cause cancer. May cause target organ effects.

Potential health effects

Eye Contact: Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing. Skin Contact: Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Prolonged or repeated exposure may cause: Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and changes in lung function tests. May be absorbed following inhalation and cause target organ effects. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May be absorbed following ingestion and cause target organ effects. Target Organ Effects: Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness. Carcinogenicity: Contains a chemical or chemicals which can cause cancer. Ingredient C.A.S. No. Class Description Regulation QUARTZ SILICA 14808-60-7 Grp. 1: Carcinogenic to International Agency for Research on Cancer humans SILICA, CRYSTALLINE (AIRBORNE SEQ677 Grp. 1: Carcinogenic to International Agency for Research on Cancer PARTICLES OF RESPIRABLE SIZE) humans SILICA, CRYSTALLINE (AIRBORNE SEQ677 Known human carcinogen National Toxicology Program Carcinogens PARTICLES OF RESPIRABLE SIZE) SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature No Data Available Flash Point 111 ºF - 113 ºF [Test Method: Closed Cup] Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available 5.2 EXTINGUISHING MEDIA Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide). 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Combustible liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions, protective equipment and emergency procedures Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Remember, adding an absorbent material does not remove a toxic, corrosivity or flammability hazard. 6.2. Environmental precautions For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Collect the resulting residue containing solution. Place in a metal container approved for transportation by appropriate authorities. Dispose of collected material as soon as possible. Clean-up methods Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill. Contain spill. Cover spill area with a fire-extinguishing foam. An aqueous film forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with detergent and water. Seal the container. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Avoid eye contact. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat, sparks, open flame, pilot lights and other sources of ignition. Ground containers securely when transferring contents. Wear low static or properly grounded shoes. No smoking while handling this material. Avoid breathing of vapors, mists or spray. Avoid skin contact. Keep out of the reach of children. Store work clothes separately from other clothing, food and tobacco products. No smoking: Smoking while using this product can result in contamination of the tobacco and/or smoke and lead to polymer fume fever caused by the formation of the hazardous decomposition products mentioned in the Reactivity Data section of this MSDS. Do not breathe dust. Avoid contact with oxidizing agents.

Storage

Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Store away from areas where product may come into contact with food or pharmaceuticals. Store away from oxidizing agents. Keep container tightly closed. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Provide appropriate local exhaust ventilation on open containers. Use in a well-ventilated area. If exhaust ventilation is not available, use appropriate respiratory protection. Do not use in a confined area or areas with little or no air movement. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborne particles. If ventilation is not adequate, use respiratory protection equipment. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact with vapors, mists, or spray. The following eye protection(s) are recommended: Safety Glasses with side shields Indirect Vented Goggles . 8.2.2 Skin Protection Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Nitrile Rubber . 8.2.3 Respiratory Protection Avoid breathing of vapors, mists or spray. Avoid breathing of dust. An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates For questions about suitability for a specific application, consult with your respirator manufacturer. 8.2.4 Prevention of Swallowing Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable. 8.3 EXPOSURE GUIDELINES Ingredient Authority Type Limit

Additional information

ALUMINUM OXIDE CMRG TWA 1 fiber/cc ALUMINUM OXIDE OSHA TWA, respirable 5 mg/m3 fraction ALUMINUM OXIDE OSHA TWA, as total dust 15 mg/m3 Benzene, 1,3-dimethyl- ACGIH TWA 100 ppm Benzene, 1,3-dimethyl- ACGIH STEL 150 ppm Benzene, 1,4-dimethyl- ACGIH TWA 100 ppm Benzene, 1,4-dimethyl- ACGIH STEL 150 ppm DECAMETHYLCYCLOPENTASILOXANE CMRG TWA 10 ppm HYDROTREATED LIGHT PETROLEUM CMRG TWA 300 ppm DISTILLATES ISOPROPYL ALCOHOL ACGIH TWA 200 ppm ISOPROPYL ALCOHOL ACGIH STEL 400 ppm ISOPROPYL ALCOHOL OSHA TWA 980 mg/m3 MINERAL OILS, HIGHLY-REFINED OILS ACGIH TWA, inhalable 5 mg/m3 fraction QUARTZ SILICA ACGIH TWA, respirable 0.025 mg/m3 fraction QUARTZ SILICA OSHA TWA concentration, 0.1 mg/m3 respirable QUARTZ SILICA OSHA TWA concentration, 0.3 mg/m3 as total dust WHITE MINERAL OIL (PETROLEUM) CMRG TWA 5 mg/m3 WHITE MINERAL OIL (PETROLEUM) CMRG STEL 10 mg/m3 SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL) SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Odor, Color, Grade: liquid, slight solvent odor General Physical Form: Liquid Autoignition temperature No Data Available Flash Point 111 ºF - 113 ºF [Test Method: Closed Cup] Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Boiling Point 92.3 ºC [Details: @ 760 mmHg] Density 0.98 - 1.01 g/ml Vapor Density > 1 [Ref Std: AIR=1] Vapor Pressure 20.5 mmHg [Details: @ 68 F(20C)] Specific Gravity 0.98 - 1.01 [Ref Std: WATER=1] Melting point No Data Available Solubility in Water Moderate Hazardous Air Pollutants 0.09 % weight [Test Method: Calculated] Volatile Organic Compounds 16.6 % weight [Test Method: calculated per CARB title 2] Volatile Organic Compounds 164 g/l [Test Method: calculated SCAQMD rule 443.1] Kow - Oct/Water partition coef No Data Available Percent volatile 81.6 % VOC Less H2O & Exempt Solvents 461 g/l [Test Method: calculated SCAQMD rule 443.1] SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: 10.1 Conditions to avoid Sparks and/or flames Heat 10.2 Materials to avoid Strong oxidizing agents Strong acids Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition or By-Products Substance Condition Formaldehyde During Combustion Carbon monoxide During Combustion Carbon dioxide During Combustion

TOXICOLOGICAL INFORMATION

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components. Not determined. CHEMICAL FATE INFORMATION Not determined. SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product in a permitted hazardous waste facility. EPA Hazardous Waste Number (RCRA): D001 (Ignitable) Since regulations vary, consult applicable regulations or authorities before disposal. SECTION 14:TRANSPORT INFORMATION ID Number(s): LB-K100-0379-4, LB-K100-0762-3, 60-4550-3278-3, 60-4550-3307-0, 60-4550-3483-9, 60-4550-5117-1, 60-4550-5286-4, 60-4550- 5287-2, 60-4550-5773-1 For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: REGULATORY INFORMATION US FEDERAL REGULATIONS Contact 3M for more information. 311/312 Hazard Categories: Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA): Ingredient C.A.S. No % by Wt ALUMINUM OXIDE 1344-28-1 3 - 7 ALUMINUM OXIDE (ALUMINUM OXIDE 1344-28-1 3 - 7 (FIBROUS FORMS ONLY)) STATE REGULATIONS Contact 3M for more information. CALIFORNIA PROPOSITION 65 Ingredient C.A.S. No.

2.1 Classification of the substance or mixture

SILICA, CRYSTALLINE (AIRBORNE None **Carcinogen PARTICLES OF RESPIRABLE SIZE) ** WARNING: contains a chemical which can cause cancer. CHEMICAL INVENTORIES The components of this product are in compliance with the chemical notification requirements of TSCA. All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS), or are exempt polymers whose monomers are listed on EINECS. Contact 3M for more information. INTERNATIONAL REGULATIONS Contact 3M for more information. WHMIS: Hazardous This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

Further information

NFPA Hazard Classification Health 2 Flammability 2 Reactivity 0 Special None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Revision Changes: Section 1: Product use information was modified. Section 7: Handling information was modified. Section 7: Storage information was modified. Section 8: Engineering controls information was modified. Section 8: Prevention of swallowing information was modified. Section 10: Hazardous decomposition or by-products table was modified. Section 8: Respiratory protection - recommended respirators information was modified. Section 8: Respiratory protection - recommended respirators was modified. Section 3: Immediate other hazard(s) was modified. Section 9: Density information was modified. Section 9: Vapor density value was modified. Section 9: Vapor pressure value was modified. Section 9: Boiling point information was modified. Section 5: Flammable limits (UE) information was modified. Section 5: Flammable limits (LEL) information was modified. Section 5: Autoignition temperature information was modified. Section 5: Flash point information was modified. Section 9: Property description for optional properties was modified. Section 9: Specific gravity information was modified. Section 9: Melting point information was modified. Section 9: Solubility in water text was modified. Section 8: Respiratory protection - recommended respirators guide was modified. Section 9: Flash point information was modified. Section 9: Flammable limits (LEL) information was modified. Section 9: Flammable limits (UEL) information was modified. Section 9: Autoignition temperature information was modified. Section 14: ID Number(s) Template 1 was modified. Section 2: Ingredient table was modified. Section 15: EPCRA 313 information was modified. Section 8: Exposure guidelines ingredient information was modified. Section 3: Carcinogenicity table was modified. Section 15: California proposition 65 ingredient information was modified. Copyright was modified.