Note: Ingredients listed on restricted chemical lists
EC/CAS
25550-51-0
Name of the chemical
Hexahydromethylphthalic anhydride [1], Hexahydro-4-methylphthalic anhydride [2], Hexahydro-1-methylphthalic anhydride [3], Hexahydro-3-methylphthalic anhydride [4] [The individual isomers [2], [3] and [4] (including their cis- and trans- stereo isomeric forms) and all possible combinations of the isomers [1] are covered by this entry]
Concentration
15 - 35
EC/CAS
21645-51-2
Name of the chemical
Aluminium hydroxide
Concentration
10-30
EC/CAS
85-42-7
Name of the chemical
Cyclohexane-1,2-dicarboxylic anhydride [1], cis-cyclohexane-1,2-dicarboxylic anhydride s
Concentration
1 - 10
EC/CAS
25068-38-6
Name of the chemical
4,4'-Isopropylidenediphenol, oligomeric reaction products with 1-chloro-2,3-epoxypropane
Concentration
1 - 5
EC/CAS
7723-14-0
Name of the chemical
Phosphorus
Concentration
1 - 5
General Information
Version
6.02
Revision date
2021-04-19
Product name
3M Scotch-Weld Structural Void Filling Compound 3460 HT FST
1.2.1 Relevant identified uses
Low Density Void Filler
supplier name
3M
Manufacturer Name
3M
Emergency telephone
1-800-364-3577, (651) 737-6501
Icons in SDS
Company Information
company name
3M
Hazard Codes
Hazard statements (CLP)
H315, H317, H318, H334, H361
Hazard statements
Code
Statements
H315
Causes skin irritation
Section 2
SECTION 2: Hazards identification
Hazard classification Serious Eye Damage/Irritation: Category 1 Skin Corrosion/Irritation: Category 2 Respiratory Sensitizer: Category 1 Skin Sensitizer: Category 1A Reproductive Toxicity: Category 2
Hazard pictograms
Corrosion | Health Hazard |
Hazard statements
Causes serious eye damage. Causes skin irritation. May cause allergy or asthma symptoms or breathing difficulties if inhaled. May cause an allergic skin reaction. Suspected of damaging fertility or the unborn child.
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. In case of inadequate ventilation wear respiratory protection. Wear protective gloves and eye/face protection. Wash thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace.
Response
IF INHALED: If breathing is difficult, remove person to fresh air and keep comfortable for breathing. If experiencing respiratory symptoms: Call a POISON CENTER or doctor/physician. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF ON SKIN: Wash with plenty of soap and water. Immediately call a POISON CENTER or doctor/physician. If skin irritation or rash occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF exposed or concerned: Get medical advice/attention.
Storage
Store locked up.
Disposal
Dispose of contents/container in accordance with applicable local/regional/national/international regulations. 40% of the mixture consists of ingredients of unknown acute inhalation toxicity.
2.1 Classification of the substance or mixture
Serious Eye Damage/Irritation: Category 1. Skin Corrosion/Irritation: Category 2. Respiratory Sensitizer: Category 1. Skin Sensitizer: Category 1A. Reproductive Toxicity: Category 2.
