Note: Ingredients listed on restricted chemical lists
EC/CAS
108-88-3
Name of the chemical
Toluene
Concentration
74% 62-1357- 00-21200- 62-1357- 00-21200- 62-1357- 00-21200- 62-1357- 00-21200- 62-1357- 00-21200- 87-2500- 87-2500- 3-7
EC/CAS
110-82-7
Name of the chemical
Cyclohexane
Concentration
<2.5
EC/CAS
110-54-3
Name of the chemical
n-Hexan (790/2009)
Concentration
5-20
EC/CAS
64741-84-0
Name of the chemical
Naphtha (petroleum), solvent-refined light
Concentration
N/A
General Information
Revision date
2012-02-02
Product name
3M Scotch-Weld Neoprene High Performance Contact Adhesive EC-1357, Grey- Green
Product Synonyms
PETROLEUM DISTILLATE
CAS No.
64741-84-0
Manufacturer Name
3M
Emergency telephone
1-800-364-3577 or (651) 737-6501 (24 hours
Icons in SDS
Company Information
company name
3m company
Section 2
SECTION 2: Hazards identification
OSHA 3.1 EMERGENCY OVERVIEW Odor, Color, Grade: grey/green, strong petroleum odor. General Physical Form: Liquid Immediate health, physical, and environmental hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. May cause allergic skin reaction. May cause target organ effects. Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
Potential health effects
Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Prolonged or repeated exposure may cause: Respiratory Effects: Signs/symptoms may include cough, shortness of breath, chest tightness, wheezing, increased heart rate, bluish colored skin (cyanosis), sputum production, changes in lung function tests, and/or respiratory failure. May be absorbed following inhalation and cause target organ effects. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May be absorbed following ingestion and cause target organ effects. Target Organ Effects: Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness. Prolonged or repeated exposure may cause: Ocular Effects: Signs/symptoms may include blurred or significantly impaired vision. Peripheral Neuropathy: Signs/symptoms may include tingling or numbness of the extremities, incoordination, weakness of the hands and feet, tremors and muscle atrophy. Olfactory Effects: Signs/symptoms may include decreased ability to detect odors and/or complete loss of smell. Neurological Effects: Signs/symptoms may include personality changes, lack of coordination, sensory loss, tingling or numbness of the extremities, weakness, tremors, and/or changes in blood pressure and heart rate. Contains a chemical or chemicals which can cause birth defects or other reproductive harm. SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature No Data Available Flash Point -14 ºF [Test Method: Tagliabue Closed Cup] Flammable Limits(LEL) 1 % volume Flammable Limits(UEL) 12.8 % volume 5.2 EXTINGUISHING MEDIA Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide). 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions, protective equipment and emergency procedures Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Avoid contact with incompatible materials listed in the Reactivity Data Section. Remember, adding an absorbent material does not remove a toxic, corrosivity or flammability hazard. 6.2. Environmental precautions For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Collect the resulting residue containing solution. Place in a metal container approved for use in transportation by appropriate authorities. The container must be lined with polyethylene plastic or contain a plastic drum liner made of polyethylene. Place in a metal container approved for transportation by appropriate authorities. Dispose of collected material as soon as possible. Clean-up methods Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill. Contain spill. Cover spill area with a fire-extinguishing foam. An aqueous film forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow
Precautionary statements
on the solvent label and MSDS. Seal the container In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Vapors may ignite explosively. May cause flash fire. Prevent build-up of vapors - open all windows and doors. Maintain vapor concentrations below recommended exposure limits. Use only with cross-ventilation. Without adequate ventilation, vapors may settle in low-lying areas. Keep away from heat, sparks, and open flame. Do not smoke or ignite matches, lighters, etc. Extinguish pilot lights and turn off stoves, ovens and other gas and electric appliances (space and water heaters, furnaces, etc.), electric motors, and other sources of ignition during adhesive use and until all vapors are gone; i.e., until the odor of vapors at the floor level has disappeared. Do not use electric light switches. Do not generate static sparks (such as by walking on carpet, etc.). Use the same precautions in the work area and all connected areas. Be sure that any people in the area follow the precautions. Attach a copy of the precautions to any other container to which this product may by transferred. Avoid prolonged breathing of vapors. Avoid eye and skin contact. Keep container closed when not in use. If work area conditions prevent compliance with any of the above precautions, do not use the product. Keep out of the reach of children. For industrial or professional use only. Not intended for consumer sale or use. Follow OTHER PRECAUTIONARY INFORMATION below.
Storage
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container tightly closed. Store away from oxidizing agents. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Use with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation on open containers. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control mist, vapor, or spray. If ventilation is not adequate, use respiratory protection equipment. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact with vapors, mists, or spray. The following eye protection(s) are recommended: Safety Glasses with side shields Indirect Vented Goggles . 8.2.2 Skin Protection Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Polymer laminate . 8.2.3 Respiratory Protection Avoid breathing of vapors, mists or spray. Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges . Select and use respiratory protection to prevent an inhalation exposure based on the results of an exposure assessment. Consult with your respirator manufacturer for selection of appropriate types of respirators. 8.2.4 Prevention of Swallowing Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Not applicable. 8.3 EXPOSURE GUIDELINES Ingredient Authority Type Limit Additional Information 2-Butanone ACGIH TWA 200 ppm 2-Butanone ACGIH STEL 300 ppm 2-Butanone OSHA TWA 590 mg/m3 ACETONE ACGIH TWA 500 ppm ACETONE ACGIH STEL 750 ppm ACETONE OSHA TWA 2400 mg/m3 CYCLOHEXANE ACGIH TWA 100 ppm CYCLOHEXANE OSHA TWA 1050 mg/m3 Hexane ACGIH TWA 50 ppm Skin Notation* Hexane OSHA TWA 1800 mg/m3 HEXANE ACGIH TWA 50 ppm Skin Notation* HEXANE OSHA TWA 1800 mg/m3 METHYL ETHYL KETONE ACGIH TWA 200 ppm METHYL ETHYL KETONE ACGIH STEL 300 ppm METHYL ETHYL KETONE OSHA TWA 590 mg/m3 Rosin ACGIH Limit value not ****Missing Sensitizer; Cntrl all exposr-low as possib established Data**** No UOM specified or needed. ROSIN ACGIH Limit value not ****Missing Sensitizer; Cntrl all exposr-low as possib established Data**** No UOM specified or needed. TOLUENE ACGIH TWA 20 ppm TOLUENE CMRG STEL 75 ppm Skin Notation* TOLUENE OSHA TWA 200 ppm TOLUENE OSHA CEIL 300 ppm ZINC OXIDE ACGIH TWA, respirable 2 mg/m3 fraction ZINC OXIDE ACGIH STEL, respirable 10 mg/m3 fraction ZINC OXIDE OSHA TWA, as fume 5 mg/m3 ZINC OXIDE OSHA TWA, respirable 5 mg/m3 fraction ZINC OXIDE OSHA TWA, as total dust 15 mg/m3 * Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye, either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption. SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL) SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Odor, Color, Grade: grey/green, strong petroleum odor. General Physical Form: Liquid Autoignition temperature No Data Available Flash Point -14 ºF [Test Method: Tagliabue Closed Cup] Flammable Limits(LEL) 1 % volume Flammable Limits(UEL) 12.8 % volume Boiling Point 132 ºF [Details CONDITIONS (acetone)] Vapor Density 3 [Ref Std: AIR=1] Vapor Pressure 180 mmHg [Details CONDITIONS @ 68F] Specific Gravity .84 [Ref Std: WATER=1] pH No Data Available Melting point No Data Available Solubility in Water Slight (less than 10%) Evaporation rate >=2 [Ref Std: WATER=1] Hazardous Air Pollutants 1.2 lb HAPS/lb solids [Test Method: Calculated] Volatile Organic Compounds 490 g/l [Test Method: calculated SCAQMD rule 443.1] Kow - Oct/Water partition coef No Data Available Percent volatile 74 % VOC Less H2O & Exempt Solvents 587 g/l [Test Method: calculated SCAQMD rule 443.1] Viscosity 200 - 1000 centipoise SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: 10.1 Conditions to avoid Sparks and/or flames 10.2 Materials to avoid Strong oxidizing agents Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition or By-Products