3M ESPE CLINPRO SEALANT

SECTION 2: Hazards identification

OSHA Hazards 3.1 EMERGENCY OVERVIEW Specific Physical Form: Liquid Odor, Color, Grade: Characteristic odor, Clear to slight yellow General Physical Form: Liquid Immediate health, physical, and environmental hazards: May cause allergic skin reaction. This document has been prepared in accordance with the U.S. OSHA Hazard Communication Standard, which requires the inclusion of all known hazards of the product or ingredients regardless of the potential risk. The risks of the hazards communicated in this document may vary depending on the potential for exposure.

Potential health effects

Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Inhalation: No health effects are expected. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse. Inhalation: No need for first aid is anticipated. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature No Data Available Flash Point Flash point > 93 °C (200 °F) Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available 5.2 EXTINGUISHING MEDIA Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide). 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: No unusual fire or explosion hazards are anticipated. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information. SECTION 6: ACCIDENTAL RELEASE MEASURES 6.1. Personal precautions, protective equipment and emergency procedures Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. 6.2. Environmental precautions For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Place in a closed container approved for transportation by appropriate authorities. Dispose of collected material as soon as possible. Clean-up methods Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Avoid eye contact. Avoid skin contact. A no-touch technique is recommended. If skin contact occurs, wash skin with soap and water. Acrylates may penetrate commonly-used gloves. If product contacts glove, remove and discard glove, wash hands immediately with soap and water and then re-glove. Wash hands after handling and before eating.

Storage

Store out of direct sunlight. Keep container in well-ventilated area. Store away from areas where product may come into contact with food or pharmaceuticals. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Use in a well-ventilated area. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact. The following eye protection(s) are recommended: Safety Glasses with side shields . 8.2.2 Skin Protection Avoid skin contact. See Section 7.1 for additional information on skin portection. 8.2.3 Respiratory Protection Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. 8.2.4 Prevention of Swallowing Do not ingest. Wash hands after handling and before eating. 8.3 EXPOSURE GUIDELINES Ingredient Authority Type Limit Additional Information ANTIMONY COMPOUNDS ACGIH TWA, as Sb 0.5 mg/m3 ANTIMONY COMPOUNDS OSHA TWA, as Sb 0.5 mg/m3 Borates ACGIH TWA, inhalable 2 mg/m3 fraction Borates ACGIH STEL, inhalable 6 mg/m3 fraction HYDROQUINONE ACGIH TWA 1 mg/m3 Sensitizer HYDROQUINONE CMRG STEL 4 mg/m3 HYDROQUINONE OSHA TWA 2 mg/m3 TITANIUM DIOXIDE ACGIH TWA 10 mg/m3 TITANIUM DIOXIDE CMRG TWA, as respirable 5 mg/m3 dust TITANIUM DIOXIDE OSHA TWA, as total dust 15 mg/m3 SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL) SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Specific Physical Form: Liquid Odor, Color, Grade: Characteristic odor, Clear to slight yellow General Physical Form: Liquid Autoignition temperature No Data Available Flash Point Flash point > 93 °C (200 °F) Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Boiling Point No Data Available Density 1.2 g/ml Vapor Density No Data Available Vapor Pressure <=27 psia [@ 131.0 ºF] Specific Gravity 1.2 [Ref Std: WATER=1] pH No Data Available Melting point Not Applicable Solubility In Water No Data Available Evaporation rate No Data Available Volatile Organic Compounds No Data Available Kow - Oct/Water partition coef Not Applicable Percent volatile No Data Available VOC Less H2O & Exempt Solvents No Data Available Viscosity Approximately 1000 centistoke SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: 10.1 Conditions to avoid None known 10.2 Materials to avoid None known Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition or By-Products