3M BRAND DESK AND OFFICE CLEANER 573

SECTION 2: Hazards identification

3.1 EMERGENCY OVERVIEW Specific Physical Form: foam Odor, Color, Grade: White foam, Lemon odor General Physical Form: Liquid Immediate health, physical, and environmental hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. The pH of this material is 10 - 12.

Potential health effects

Eye Contact: Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing. Skin Contact: Contact with the skin during product use is not expected to result in significant irritation. Inhalation: Prolonged or repeated exposure may cause: Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Ingestion: No health effects are expected. SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: No need for first aid is anticipated. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: No need for first aid is anticipated. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature No Data Available Flash Point 30 ºF [Test Method Open Cup] [Details specific method D92] Flammable Limits - LEL 1.80 % Flammable Limits - UEL 8.40 % [Details: for isobutane.] 5.2 EXTINGUISHING MEDIA Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide). 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Unusual Fire and Explosion Hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information. SECTION 6: ACCIDENTAL RELEASE MEASURES Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. If possible, seal leaking container. Place leaking containers in a well-ventilated area, preferably an operating exhaust hood, or if necessary outdoors on an impermeable surface until appropriate packaging for the leaking container or its contents is available. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam designed for use on solvents, such as alcohols and acetone, that can dissolve in water. An AR - AFFF type foam is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a toxic, corrosivity or flammability hazard. Collect as much of the spilled material as possible using non-sparking tools. Clean up residue with detergent and water. Collect the resulting residue containing solution. Place in an approved metal container. Seal the container. Dispose of collected material as soon as possible. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Avoid eye contact. Keep out of the reach of children. Aerosol container contains flammable gas under pressure. Keep away from heat, sparks, open flame, pilot lights and other sources of ignition. Avoid eye contact with vapors, mists, or spray. Avoid breathing of vapors, mists or spray. Avoid prolonged or repeated skin contact. Ground containers securely when transferring contents. Wear low static or properly grounded shoes. Do not spray near flames or sources of ignition. Avoid static discharge. Contents may be under pressure, open carefully. No smoking while handling this material. Avoid contact with oxidizing agents.

Storage

Store away from heat. Store out of direct sunlight. Keep container tightly closed. Store away from acids. Store away from oxidizing agents. Keep container in well-ventilated area. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Do not use in a confined area or areas with little or no air movement. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact with vapors, mists, or spray. Avoid eye contact. 8.2.2 Skin Protection Avoid prolonged or repeated skin contact. Gloves not normally required. 8.2.3 Respiratory Protection Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. Avoid breathing of vapors, mists or spray. 8.2.4 Prevention of Swallowing Not applicable. 8.3 EXPOSURE GUIDELINES Ingredient Authority Type Limit Additional Information ETHANOLAMINE ACGIH TWA 3 ppm ETHANOLAMINE ACGIH STEL 6 ppm ETHANOLAMINE OSHA TWA 3 ppm Table Z-1A ETHANOLAMINE OSHA STEL 6 ppm Table Z-1A ISOPROPYL ALCOHOL ACGIH TWA 200 ppm Table A4 ISOPROPYL ALCOHOL ACGIH STEL 400 ppm Table A4 ISOPROPYL ALCOHOL OSHA TWA 400 ppm Table Z-1A ISOPROPYL ALCOHOL OSHA STEL 500 ppm Table Z-1A SOURCE OF EXPOSURE LIMIT DATA: ACGIH: American Conference of Governmental Industrial Hygienists CMRG: Chemical Manufacturer Recommended Guideline OSHA: Occupational Safety and Health Administration AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL) SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Specific Physical Form: foam Odor, Color, Grade: White foam, Lemon odor General Physical Form: Liquid Autoignition temperature No Data Available Flash Point 30 ºF [Test Method Open Cup] [Details specific method D92] Flammable Limits - LEL 1.80 % Flammable Limits - UEL 8.40 % [Details: for isobutane.] Boiling point Not Applicable Density 1 g/ml Vapor Density No Data Available Vapor Pressure 31 - 43 psi [@ 70 ºF] [Details: (aerosol can pressure)] Specific Gravity Approximately 1 [Ref Std: WATER=1] Melting point Not Applicable Solubility In Water 100.00 % Evaporation rate =1.00 [Ref Std WATER=1] [Details product as applied (without propellant)] Volatile Organic Compounds 55 - 115 g/l Percent volatile 96 - 98 % weight VOC Less H2O & Exempt Solvents 702 - 831 g/l Viscosity Not Applicable SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: Heat; Sparks and/or flames Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition or By-Products