3M Bondo(r) Home Solutions (BHS) White Cream Hardener

SECTION 2: Hazards identification

29 CFR 1910.1200) 3.1 EMERGENCY OVERVIEW Specific Physical Form: Viscous Odor, Color, Grade: Red paste with slight ester odor General Physical Form: Solid Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and explode. Dust clouds of this material in combination with an ignition source may be explosive. May cause allergic skin reaction.

Potential health effects

Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May be absorbed following ingestion and cause target organ effects. Target Organ Effects: Prolonged or repeated exposure may cause: Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and jaundice. Kidney/Bladder Effects: Signs/symptoms may include changes in urine production, abdominal or lower back pain, increased protein in urine, increased blood urea nitrogen (BUN), blood in urine, and painful urination. SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature No Data Available Flash Point Not Applicable Flammable Limits - LEL Not Applicable Flammable Limits - UEL Not Applicable 5.2 EXTINGUISHING MEDIA Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide). 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Dust clouds of this material in combination with an ignition source may be explosive. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information. SECTION 6: ACCIDENTAL RELEASE MEASURES Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non- sparking tools. Ventilate the area with fresh air. Contain spill. Avoid contact with incompatible materials listed in the Reactivity Data Section. Collect as much of the spilled material as possible using non-sparking tools. Use wet sweeping compound or water to avoid dusting. Sweep up. Clean up residue. Collect the resulting residue containing solution. Place in a metal container approved for transportation by appropriate authorities. Cover, but do not seal for 48 hours. Dispose of collected material as soon as possible. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat, sparks, open flame, pilot lights and other sources of ignition. Avoid static discharge. Avoid eye contact with vapors, mists, or spray. Keep out of the reach of children. Avoid breathing of dust created by cutting, sanding, grinding or machining. Avoid eye contact with dust or airborne particles.

Storage

Store away from heat. Store out of direct sunlight. Keep container tightly closed. Do not heat under confinement to avoid risk of explosion SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Provide appropriate local exhaust for cutting, grinding, sanding or machining. Do not use in a confined area or areas with little or no air movement. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborne particles. If ventilation is not adequate, use respiratory protection equipment. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact with vapors, mists, or spray. The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles. 8.2.2 Skin Protection Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials. Gloves made from the following material(s) are recommended: Polyethylene/Ethylene Vinyl Alcohol. Use an additional glove (e.g. supported PVC or Nitrile) over the PE/EVAL glove, and change the over-glove frequently. 8.2.3 Respiratory Protection Avoid breathing of vapors, mists or spray. Avoid breathing of dust created by cutting, sanding, grinding or machining. Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with

Additional information

BENZOYL PEROXIDE ACGIH TWA 5 mg/m3 Table A4 BENZOYL PEROXIDE

TOXICOLOGICAL INFORMATION

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components. Not determined. CHEMICAL FATE INFORMATION Not determined. SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal Method: Incinerate uncured product in a permitted hazardous waste incinerator in the presence of a combustible material. As a disposal alternative, dispose of waste product in a permitted hazardous waste facility. EPA Hazardous Waste Number (RCRA): D001 (Ignitable), D003 (Reactive) Since regulations vary, consult applicable regulations or authorities before disposal. SECTION 14:TRANSPORT INFORMATION ID Number(s): LB-K100-0534-6, LB-K100-0534-7, LB-K100-0534-8, LB-K100-0534-9, LB-K100-0540-5, 70-0080-0309-0 Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material. SECTION 15: REGULATORY INFORMATION US FEDERAL REGULATIONS Contact 3M for more information. 311/312 Hazard Categories: Fire Hazard - No Pressure Hazard - No Reactivity Hazard - Yes Immediate Hazard - Yes Delayed Hazard - Yes Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372

Further information

NFPA Hazard Classification Health 2 Flammability 2 Reactivity 1 Special Oxidizer National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Revision Changes: Section 1: Product name was modified. Section 1: Division name was modified. Copyright was modified. Section 8: Skin protection - recommended gloves information was modified. Page Heading: Product name was modified. Section 8: Skin protection comment was added. DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M. 3M MSDSs are available at www.3M.com SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: 3M(TM) Bondo Home Solutions(TM) Wood Filler, PN 20082 Part A MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center St. Paul, MN 55144-1000 EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours) Issue date 11/06/2008 Supercedes Date: 09/19/2008 Document Group: 24-8195-0 Product Use: Intended Use: Automotive SECTION 2: INGREDIENTS Ingredient C.A.S. No. % by Wt PROPRIETARY RESIN Trade Secret 15 - 40 STYRENE MONOMER 100-42-5 10 - 30 LIMESTONE 1317-65-3 10 - 30 TALC 14807-96-6 10 - 30 MAGNESIUM CARBONATE 546-93-0 7 - 13 SODIUM SILICATE 1344-09-8 3 - 7 QUATERNARY AMMONIUM COMPOUNDS 68911-87-5 0.5 - 1.5 QUARTZ SILICA 14808-60-7 <= 0.40845 SECTION 3: HAZARDS IDENTIFICATION 3.1 EMERGENCY OVERVIEW Odor, Color, Grade: Yellow putty with pungent organic odor General Physical Form: Liquid Immediate health, physical, and environmental hazards: Flammable liquid and vapor. Closed containers exposed to heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back. May cause target organ effects. Contains a chemical or chemicals which can cause cancer. MATERIAL SAFETY DATA SHEET 3M(TM) Bondo Home Solutions(TM) Wood Filler, PN 20082 Part A 11/06/2008 3.2 POTENTIAL HEALTH EFFECTS Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Prolonged or repeated exposure may cause: Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and changes in lung function tests. May be absorbed following inhalation and cause target organ effects. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May be absorbed following ingestion and cause target organ effects. Target Organ Effects: Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea, slowed reaction time, slurred speech, giddiness, and unconsciousness. Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and jaundice. Auditory Effects: Signs/symptoms may include hearing impairment, balance dysfunction and ringing in the ears. Prolonged or repeated exposure may cause: Neurological Effects: Signs/symptoms may include personality changes, lack of coordination, sensory loss, tingling or numbness of the extremities, weakness, tremors, and/or changes in blood pressure and heart rate. Ocular Effects: Signs/symptoms may include blurred or significantly impaired vision. Kidney/Bladder Effects: Signs/symptoms may include changes in urine production, abdominal or lower back pain, increased protein in urine, increased blood urea nitrogen (BUN), blood in urine, and painful urination. Immunological Effects: Signs/symptoms may include alterations in the number of circulating immune cells, allergic skin and /or respiratory reaction, and changes in immune function. Carcinogenicity: Contains a chemical or chemicals which can cause cancer. MATERIAL SAFETY DATA SHEET 3M(TM) Bondo Home Solutions(TM) Wood Filler, PN 20082 Part A 11/06/2008 Ingredient C.A.S. No. Class Description Regulation QUARTZ SILICA 14808-60-7 Group 1 International Agency for Research on Cancer QUARTZ SILICA 14808-60-7 Known human carcinogen National Toxicology Program Carcinogens STYRENE MONOMER 100-42-5 Group 2B International Agency for Research on Cancer