3304P 3M ESPE KETAC NANO PRIMER

SECTION 2: Hazards identification

29 CFR 1910.1200) 3.1 EMERGENCY OVERVIEW Odor, Color, Grade: Clear, yellow liquid. General Physical Form: Liquid Immediate health, physical, and environmental hazards: May cause severe eye irritation. May cause allergic skin reaction.

Potential health effects

Eye Contact: Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the cornea, and impaired vision. Skin Contact: Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. SECTION 4: FIRST AID MEASURES 4.1 FIRST AID PROCEDURES The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are followed. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention. Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical attention. Wash contaminated clothing and clean shoes before reuse. Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention. If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never give anything by mouth to an unconscious person. Get medical attention. SECTION 5: FIRE FIGHTING MEASURES 5.1 FLAMMABLE PROPERTIES Autoignition temperature No Data Available Flash Point 219 ºF [Test Method: Closed Cup] Flammable Limits - LEL No Data Available Flammable Limits - UEL No Data Available 5.2 EXTINGUISHING MEDIA Ordinary combustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam). 5.3 PROTECTION OF FIRE FIGHTERS Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus (SCBA). Unusual Fire and Explosion Hazards: Not applicable. Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition information. SECTION 6: ACCIDENTAL RELEASE MEASURES Accidental Release Measures: Dispose of collected material as soon as possible. Observe precautions from other sections. Call 3M- HELPS line (1-800-364-3577) for more information on handling and managing the spill. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and MSDS. In the event of a release of this material, the user should determine if the release qualifies as reportable according to local, state, and federal regulations. SECTION 7: HANDLING AND STORAGE 7.1 HANDLING Avoid eye contact. Avoid skin contact. A no-touch technique is recommended. If skin contact occurs, wash skin with soap and water. Acrylates may penetrate commonly-used gloves. If product contacts glove, remove and discard glove, wash hands immediately with soap and water and then re-glove. Do not ingest. Wash hands after handling and before eating.

Storage

Store out of direct sunlight. Store in a cool, dry place. SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION 8.1 ENGINEERING CONTROLS Not applicable. 8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE) 8.2.1 Eye/Face Protection Avoid eye contact. The following eye protection(s) are recommended: Safety Glasses with side shields. 8.2.2 Skin Protection Avoid skin contact. See Sect. 7.1 for more information about skin protection. 8.2.3 Respiratory Protection Under normal use conditions, airborne exposures are not expected to be significant enough to require respiratory protection. 8.2.4 Prevention of Swallowing Do not ingest. Wash hands after handling and before eating. 8.3 EXPOSURE GUIDELINES None Established SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Odor, Color, Grade: Clear, yellow liquid. General Physical Form: Liquid Autoignition temperature No Data Available Flash Point 219 ºF [Test Method: Closed Cup] Flammable Limits - LEL No Data Available Flammable Limits - UEL No Data Available Boiling point > 219 ºF Density 1.1 g/cm3 Vapor Density No Data Available Vapor Pressure No Data Available Specific Gravity 1.1 pH 3 Melting point Not Applicable Solubility in Water Complete Evaporation rate No Data Available Kow - Oct/Water partition coef Not Applicable Viscosity No Data Available SECTION 10: STABILITY AND REACTIVITY Stability: Stable. Materials and Conditions to Avoid: 10.1 Conditions to avoid None known 10.2 Materials to avoid None known Hazardous Polymerization: Hazardous polymerization will not occur. Hazardous Decomposition or By-Products Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion

TOXICOLOGICAL INFORMATION

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its components. Not determined. CHEMICAL FATE INFORMATION Not determined. SECTION 13: DISPOSAL CONSIDERATIONS Waste Disposal Method: Dispose of completely cured (or polymerized) wastes in a sanitary landfill. As a disposal alternative, dispose of waste product in a facility permitted to accept chemical waste. EPA Hazardous Waste Number (RCRA): Not regulated Since regulations vary, consult applicable regulations or authorities before disposal. SECTION 14:TRANSPORT INFORMATION ID Number(s): LE-F100-0193-4, LE-F100-0743-8, 70-2010-5080-7 Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this material. SECTION 15: REGULATORY INFORMATION US FEDERAL REGULATIONS Contact 3M for more information. 311/312 Hazard Categories: Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No STATE REGULATIONS Contact 3M for more information. CHEMICAL INVENTORIES This material contains one or more substances not listed on the TSCA Inventory. Commercial use of this material is regulated by the FDA. Contact 3M for more information. INTERNATIONAL REGULATIONS Contact 3M for more information. This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

Further information

NFPA Hazard Classification Health 2 Flammability 0 Reactivity 0 Special None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Revision Changes: Section 1: Product name was modified. Copyright was modified. Page Heading: Product name was modified. Section 9: Property description for optional properties was added. Section 14: ID Number Heading Template 1 was added. Section 14: ID Number(s) Template 1 was added. Section 2: Ingredient table was added. Section 8: Exposure guidelines information - none - was added. 10.1 Conditions to avoid was added. 10.2 Materials to avoid was added. Section 6: Release measures information was added. Section 10: Materials to avoid physical property was added. Section 10: Conditions to avoid physical property was added. Section 6: Release measures information was deleted. Section 10: Materials and conditions to avoid physical property was deleted. DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M. 3M MSDSs are available at www.3M.com SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: 3M™ ESPE™ KETAC™ NANO LIGHT-CURE GLASS IONOMER RESTORATIVE PASTE A MANUFACTURER: 3M DIVISION: 3M ESPE Dental Products ADDRESS: 3M Center St. Paul, MN 55144-1000 EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours) Issue date 10/21/09 Supercedes Date: 09/30/09 Document Group: 22-4947-2 Product Use: Intended Use: Dental product Limitations on Use: For use only by dental professionals Specific Use: Dental restorative SECTION 2: INGREDIENTS Ingredient C.A.S. No. % by Wt SILANE TREATED GLASS NONE 40 - 55 SILANE TREATED ZIRCONIA Unknown 20 - 30 POLYETHYLENE GLYCOL DIMETHACRYLATE (PEGDMA) 25852-47-5 5 - 15 SILANE TREATED SILICA 248596-91-0 5 - 15 2-HYDROXYETHYL METHACRYLATE (HEMA) 868-77-9 1 - 15 GLASS POWDER 65997-17-3 < 5 BISPHENOL A DIGLYCIDYL ETHER DIMETHACRYLATE (BISGMA) 1565-94-2 < 5 TRIETHYLENE GLYCOL DIMETHACRYLATE (TEGDMA) 109-16-0 < 1 SECTION 3: HAZARDS IDENTIFICATION 3.1 EMERGENCY OVERVIEW MATERIAL SAFETY DATA SHEET 3M™ ESPE™ KETAC™ NANO LIGHT-CURE GLASS IONOMER RESTORATIVE PASTE A 10/21/09 Specific Physical Form: Paste Odor, Color, Grade: Resin odor, Opaque, tooth-colored paste of various shades General Physical Form: Solid Immediate health, physical, and environmental hazards: May cause allergic skin reaction. This document has been prepared in accordance with the U.S. OSHA Hazard Communication Standard, which requires the inclusion of all known hazards of the product or ingredients regardless of the potential risk. The risks of the hazards communicated in this document may vary depending on the potential for exposure. 3.2 POTENTIAL HEALTH EFFECTS Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Skin Contact: Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Inhalation: This product may have a characteristic odor; however, no adverse health effects are anticipated. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.