Note: Ingredients listed on restricted chemical lists
EC/CAS
1309-48-4
Name of the chemical
magnesium oxide
Concentration
20-<50%
EC/CAS
7789-75-5
Name of the chemical
Calcium fluoride
Concentration
10-<20%
EC/CAS
1344-28-1
Name of the chemical
aluminium oxide
Concentration
10-<20%
EC/CAS
1344-09-8
Name of the chemical
Silicic acid, sodium salt
Concentration
5-<10%
EC/CAS
14464-46-1
Name of the chemical
Cristobalit (s. u. TRGS 906)
Concentration
1-<5%
EC/CAS
14808-60-7
Name of the chemical
Silica, crystalline
Concentration
1-<5%
EC/CAS
7631-86-9
Name of the chemical
Silver adsorbed on silicon dioxide
Concentration
1-<5%
EC/CAS
1305-78-8
Name of the chemical
Calcium oxide
Concentration
1-<5%
EC/CAS
68855-54-9
Name of the chemical
diatomaceous earth, soda ash flux-calcined
Concentration
1-<5%
EC/CAS
13463-67-7
Name of the chemical
Reaction mass of titanium dioxide and silver chloride
Concentration
0.1-<1%
General Information
Version
7.0
Revision date
2025-10-09
Product name
LA492 FLUX
1.2.1 Relevant identified uses
SAW (Submerged Arc Welding)
1.2.2. Uses advised against
Not known. Read this SDS before using this product
Emergency telephone
+1 (888) 609-1762, +1 (216) 383-8962, +1 (216) 383-8966, +1 (216) 383-8969
Icons in SDS
Company Information
company name
3E Company
GHS Information
Signal word
Warning
Hazard Codes
Hazard statements (CLP)
H351
Hazard statements
Code
Statements
H351
Suspected of causing cancer
Section 2
SECTION 2: Hazards identification
Classified according to the criteria of the Globally Harmonized System of Classification and Labeling of Chemicals (GHS). The product contains less than 0.1% of respirable crystalline silica. Emergency Overview Form Granular Physical state Solid
Hazard statements
Welding arc and sparks can ignite combustible and flammable products. Arc rays can injure eyes and burn skin. Electric shock can kill. Hazard Classification Suspected of causing cancer.
Health hazards
Carcinogenicity Category 2
Signal word
Warning
Prevention
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves/ protective clothing/ eye protection/ face protection.
Response
IF exposed or concerned: Get medical advice/attention.
Storage
Store locked up.
Disposal
Dispose of contents/ container to an approved facility in accordance with local, regional, national and international regulations.
Other hazards which do not result in classification
Electrical Shock can kill. If welding must be performed in damp locations or with wet clothing, on metal structures or when in cramped positions such as sitting, kneeling or lying, or if there is a high risk of unavoidable or accidental contact with work piece, use the following equipment: Semiautomatic DC Welder, DC Manual (Stick) Welder, or AC Welder with Reduced Voltage Control. Arc rays can injure eyes and burn skin. Welding arc and sparks can ignite combustibles and flammable materials. Overexposure to welding fumes and gases can be hazardous. Read and understand the manufacturer’s instructions, Safety Data Sheets and the precautionary labels before using this product. Refer to Section 8. Substance(s) formed under the The welding fume produced from this welding electrode may contain the conditions of use following constituent(s) and/or their complex metallic oxides as well as solid particles or other constituents from the consumables, base metal, or base metal coating not listed below. Chemical Identity Carbon dioxide Carbon monoxide Nitrogen dioxide Ozone CAS-No. 124-38-9 630-08-0 10102-44-0 10028-15-6
2.1 Classification of the substance or mixture
Health Hazards Carcinogenicity
